Publicidad
Idiomas disponibles
Idiomas disponibles
To Install an Air Fitting
1. Wrap the male end of the fitting with thread seal tape
prior to assembly to eliminate air leaks.
2. To install a 1/4" (6.4 mm) fitting: screw it directly into the
air inlet and tighten firmly. nOTE: If a cap is in the air
inlet, remove it prior to inserting the fitting.
3. To install a 3/8" (9.5 mm) fitting: screw the fitting into the
3/8" (9.5 mm) adapter and then into the air inlet of the
tool and tighten firmly.
Preparing the Tool (Fig. B)
WARNING: Read the section titled IMPORTANT
SAFETY INSTRUCTIONS at the beginning of this
manual. Always wear proper eye [ANSI Z87.1 (CAN/
CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)]
when operating this tool. Keep the fastener pointed
away from yourself and others. For safe operation,
complete the following procedures and checks before
each use of the fastener.
NOTICE: These nailers are designed to be used
without oil.
•
Before you use the tool, be sure that the compressor
tanks have been properly drained. nOTE: Use a filter and
regulator when possible.
•
Wear proper eye, hearing and respiratory protection.
•
Remove all fasteners from the magazine.
•
Check for smooth and proper operation of contact trip
and pusher assemblies. Do not use tool if either assembly
is not functioning properly. NEVER use a tool that has the
contact trip restrained in the up position.
•
Check air supply: Ensure air pressure does not exceed
operating limits; 60 to 100 p.s.i.g., (4.1 to 6.9 kg/cm
Keep tool pointed away from yourself and others.
•
Connect air hose.
•
Check for audible leaks around valves and gaskets. Never
use a tool that leaks or has damaged parts.
Using the Secondary Trigger (Fig. A)
WARNING: To reduce the risk of injury, Always wear
proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing
protection [ANSI S12.6 (S3.19)] when operating
this tool.
WARNING: Do not keep trigger depressed when tool is
not in use. Serious personal injury may result.
WARNING: Disconnect air line from tool and remove
fasteners from magazine before making adjustments.
Serious personal injury may result.
The tool is locked off until the secondary trigger
is depressed.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supplyremove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start‑upactuation can
cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
11
.
Loading Fasteners PIN138 (Fig. A, B, E)
WARNING: Keep the tool pointed away from yourself
and others. Serious personal injury may result.
WARNING: Never load nails with the trigger or triggers
activated. Personal injury may result.
1. Read all Safety Warnings before using tool.
2. Connect the tool to air supply.
3. Push magazine release
back. Make sure the primary and secondary trigger
are released.
4. Insert fasteners into the side of the magazine. For
fasteners with arrows the direction arrow printed on
the fasteners should point down into the bottom of
magazine. If no arrow is printed on the fasteners the
nail points should point down into the bottom of the
magazine. nOTE: Make sure fasteners are placed firmly
against lower ledge of magazine.
5. Push magazine closed until it locks in place. Make sure
the magazine snaps into place.
6. Observe low nail indicator window
needed. nOTE: The tool will not fire when only a few
fasteners are left in the magazine, reload fasteners to
).
2
begin firing again.
Actuating Tool (Fig. A, F)
WARNING: To reduce the risk of injury, Always wear
proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing
protection [ANSI S12.6 (S3.19)] when operating
this tool.
WARNING: A nail will fire each time the trigger is
depressed which could result in accidental actuation.
1. Place the nosepiece
2. Depress the secondary trigger
Now depress the trigger. A fastener is fired each time the
primary trigger is depressed.
CAUTION: Each time a fastener is fired, a blast of air
will be exhausted from the rear exhaust. Keep your face
away from this area.
2
Depth Adjustment
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply remove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental actuation can cause injury.
CAUTION: Air pressure in excess of that required can
cause premature wear and/or damage to the tool.
English
5
and pull magazine
6
7
and reload when
8
against the work surface.
2
to unlock the trigger
1
.
7
Publicidad
