Elta 6925 Manual De Instrucciones página 27

FORWARD/BACKWARD SEARCH
Press and hold SKIP/SEARCH UP/DOWN buttons during play to scan the disc
at high speed. When the desired section of the disc is found, release the button.
Normal play will resume.
UP ...............................................FORWARD
DOWN .........................................REVERSE
1. If you press and hold the UP button while playing, it will scan the disc
forward from the current played track at high speed.
2. If you press and hold the DOWN button while playing, it will scan the disc
backward from the current played track at high speed.
ANTI-SHOCK PROTECTION
A special circuitry inside the player guarantees that there will be no sound
skipping when the player is subject to shock and shaking in music playback. The
laser scans the CD/MP3 disc and saves data for up to 60/120 seconds ahead of
where the playback is on the disc. In case of shocks or shaking or vibrations, the
player reads from the memory until the laser can read CD again. But if there is
too much vicious vibration or shaking exerted on the player, the player may
malfunction and sound skipping is caused.
When this happens, place the player on a level table where no vibration will be
brought. Normal sound will resume immediately.
PROGRAMMED PLAY
The tracks on the disc can be programmed for play in any order (Up to 20 tracks
can be programmed).
Note: This can only be done during stop state.
1. Press the CD PROGRAM button in stop mode, "PROGRAM" and program
number " " are shown in the display.
2. Press the UP or DOWN SKIP/SEARCH button to select the first track to be
programmed.
3. Press the CD PROGRAM button. The first track number is now stored into
memory, program number changes to "
4. Repeat steps 2 and 3 to program additional tracks.
5. After programming is finished, press the PLAY/PAUSE button.
Programmed play begins from the first programmed track.
The player stops automatically after all programmed tracks have been
played. To play the same programmed tracks again, press the
PLAY/PAUSE button.
" waiting for your next selection.
- 51 -
In stop mode, press the STOP button once, "PROGRAM" disappears
from the display and the programmed tracks in the memory will be
cleared. The memory will also be cleared if the disc compartment is
opened, or power is turned off.
SINGLE TRACK REPEAT
Press the CD MODE button once in stop mode or playing mode, "REPT 1"
appears in the display, press the SKIP/SEARCH UP/DOWN buttons to select
your favorite song (In stopping mode pressing the PLAY/PAUSE Button again is
required).
This plays one song over and over till you press the STOP button or press the
MODE button continuously to return to the normal play mode.
ALL TRACKS REPEAT
Press the CD MODE button twice in stop mode or playing mode, "REPT ALL"
shows in the display (In stopping mode pressing the PLAY/PAUSE Button again
is required.) .
All songs will keep playing in sequence 1. 2. 3 etc. and all songs will repeat over
again until you press the STOP button or press the CD MODE button
continuously to return to the normal play mode.
INTRO SCAN PLAY
1. Press the CD MODE button thrice in stop mode or playing mode.
2. "INTRO" shows in the display, press the PLAY/PAUSE button. The first 10
seconds of each track from track 1 will be played in order.
RANDOM PLAY
Press the MODE button fourth in stop mode or playing mode. "RANDOM" shows
in the display; press the PLAY/PAUSE button.
All tracks on the disc will be played in random order selected by CD player.
MP3 DISC SECTION
TRACK-SELECTING PLAYBACK
☛ You can press SKIP/ SEARCH UP/DOWN buttons to select the tracks you
require, the concrete operations are as same as the operations on section of
CD.
☛ During Mp3 disc playing, press ALBUM/10+ button once to select the track
ten tracks ahead of the current track. Press this button continuously to
select track ahead of the current one, at the rate of ten tracks per press.
- 52 -