BEGLEC JB Systems Light DSP-12 Manual De Instrucciones página 6

ENGLISH
MENU ITEMS
• DMX FAIL:
The DSP12 works with analog 0/10V or digital DMX-512 input signals. DMX-signals
have priority to the analog inputs. This means that you can only use the analog
inputs when no DMX-signal is detected. When the DMX-signal is not present you
have 3 options:
• Hold:
In case of DMX-fail the DSP12 keeps the last scene on the outputs.
• Press "menu" and "up/down" until the display shows "Dmx fail".
• Press "menu" again: the display shows one of the 3 options.
• Press "up/down" until the display shows "Hold"
• Press "esc" to store this option and leave the menu.
• Analog:
In case of DMX-fail the DSP12 goes in analog 0/10V mode.
• Press "menu" and "up/down" until the display shows "Dmx fail".
• Press "menu" again: the display shows one of the 3 options.
• Press "up/down" until the display shows "Analog"
• Press "esc" to store this option and leave the menu.
• Prog 01 ... Prog 12:
In case of DMX-fail the DSP12 shows one of the 12 built-in patterns.
• Press "menu" and "up/down" until the display shows "Dmx fail".
• Press "menu" again: the display shows one of the 3 options.
• Press "up/down" until the display shows the desired program (Prog 01 ... 12)
• Press "esc" and "up/down" buttons to select the proper speed.
• Press "esc" to store the selected speed and leave the menu.
• PRESET:
The DSP12 can work without a controller for the input signals. This is a good option
if you just need a certain output level on each channel over a long time (shops,
exhibition booths, pubs etc...) This can be done with the Preset option. You can set
a certain level for all channels at once or for each individual channel.
• Preset All channels:
• Press "menu" and "up/down" until the display shows "Preset".
• Press "menu" again: the display shows one of the 2 options.
• Press "up/down" until the display shows "All"
• Press "menu" to select this option.
• Press "up/down" to set the desired overall level.
• Press "esc" to store the selected level and leave the menu.
• Preset individual channels:
• Press "menu" and "up/down" until the display shows "Preset".
• Press "menu" again: the display shows one of the 2 options.
• Press "up/down" until the display shows "Single"
• Press "menu" to select this option: the display shows the channel number on
the first row and the dimming value on the second row.
• Press "menu" to toggle between both rows.
• Press "up/down" to set the desired dimming levels and channel numbers until
all channels are set.
JB SYSTEMS®
OPERATION MANUAL
7/60 DSP12
ENGLISH
• Press "esc" to store the selected presets and leave the menu.
• CURVE:
With the DSP12 you can select a different working mode (curve) for each individual
channel. This is a nice feature if you need to switch light effects on/off while at the
same time you have to dim lamps. 3 Curves are available:
• Select a curve for all channels:
• Press "menu" and "up/down" until the display shows "Curve".
• Press "menu" again: the display shows one of the 2 options.
• Press "up/down" until the display shows "All"
• Press "menu" to select this option.
• Press "up/down" to select one the 3 curves
• Press "esc" to store the selected curve and leave the menu.
• Select a curve for individual channels:
• Press "menu" and "up/down" until the display shows "Curve".
• Press "menu" again: the display shows one of the 2 options.
• Press "up/down" until the display shows "Single"
• Press "menu" to select this option: the display shows the channel number on
the first row and the curve on the second row.
• Press "menu" to toggle between both rows.
• Press "up/down" to set the desired curves and channel numbers until all
channels are set.
• Press "esc" to store the selected curves and leave the menu.
• PREHEAT:
On the DSP12 you can set a preheat level up to 50% for all channels in one time or
for each channel separately. While the preheat function keeps the lamp filament at a
certain temperature, the turn on current of the lamp is much lower. This extends the
lamp life considerably in many cases.
• Preheat on all channels:
• Press "menu" and "up/down" until the display shows "Preheat".
• Press "menu" again: the display shows one of the 2 options.
• Press "up/down" until the display shows "All"
• Press "menu" to select this option.
• Press "up/down" to set the desired overall level.
• Press "esc" to store the selected level and leave the menu.
JB SYSTEMS®
OPERATION MANUAL
8/60 DSP12