Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
it returns to the charging base in a smart and direct way once the cleaning is over. It features
Total Surface function, therefore the robot cleans the whole surface, returning to the charging
base if necessary until it finishes it. Once it has completed cleaning, the robot will operate in
Random mode until it runs out of battery.
Edge mode
Select this mode from the App or the remote control, the robot will clean along the edges and
will return to the charging base through its smart technology once it has finished. If there is no
charging base, the robot will return to the starting point.
Area mode
Select this mode from the App, the robot will clean 2*2 m in zigzag motion and will return to the
starting point. The robot will not create any map under this mode.
Random mode
Select this mode from the App, the robot will start cleaning randomly and then will return to
the charging base with its smart technology once it runs out of battery. The robot will not
create any map under this mode.
Gyro mode
Select this mode from the App. When this mode is activated, the robot will carry out a whole
cleaning cycle in zig zag and then in Edge mode. Once it has finished, it will automatically
return to the charging base. If the robot has not started cleaning from the charging base, it will
return to the starting point.
Twice mode
Select this mode from the App, the robot will carry out 2 whole cleaning cycles with Gyro mode.
When the cycle is completed, it will return to the charging base with its smart technology.
Scrubbing mode
Select this mode from the robot buttons or from the App. When this mode is activated, the
robot moves in a swaying motion, simulating real scrubbing moves.
It starts off cleaning in zig zag motion, then in Edge mode, and finally returns to the charging
base taking the straightest way and memorizing the route. If it runs out of battery before
finishing, it will recharge and the resume cleaning until finished.
Use the App to enter the water intensity mode and select the desired intensity: 1, 2 or 3. When
this mode is activated, the robot will carry out a cleaning cycle in Gyro mode and then in Edge
mode, moving 2 m to the front and the 1 to the back consecutively, simulating human scrubbing
moves. It will finish off in Random mode. If it runs out of battery before finishing, it will recharge
and then resume cleaning until finished. Then, it will finally return to the charging base.
34
Warnings:
Do not use the mop outdoors.
Remove the carpets before operating the robot under this mode.
During operation, control the water level on the Wet & dry tank. If it empties, fill it up again
before continuing scrubbing.
Take the Wet & dry tank and the mop out before charging the robot.
Note: In order to ensure perfect scrubbing, moisten the mop before starting scrubbing.
Manual mode
Use the direction buttons on the remote control or on the App to take the robot to the specific
points where you want it to clean.
Back home mode
This mode can be activated from the robot, the App or the remote control at any point of any
cleaning cycle. Once it is activated, the robot will automatically return to the charging base.
Spiral mode
Select this mode for the robot to carry out an intensive cleaning of a specific spot. It will start
cleaning at a specific point and will move outwards in a spiral motion. Then, it will return to
the starting point in a spiral motion again. Once it finishes at the starting point, it will return to
the charging base.
7. CLEANING AND MAINTENANCE
Main brush and silicone brush
Turn the robot around and press the main brush's release button to take the cover out.
Take the main brush out and clean the compartment.
Clean the main brush with the provided tools and use water and soap if necessary.
Place the main brush in its position and fasten the cover's clip.
Recommendation: Replace the main brush every 6-12 months to ensure efficient operating
(depending on the frequency and type of use).
Cepillo Jalisco (brush)
To clean the Jalisco brush, follow the previous section's steps to take it out and clean it with
water.
Dry it thoroughly before assembling it back in order to ensure efficient operation.
1. Main brush cover
2. Tab
3. Main brush
ENGLISH
35
Publicidad
