AVE VI2F-PIT4B Manual De Instrucciones página 3

ENG
VI2F-PIT4B INDOOR STATION WITH 4.3" DISPLAY - 2-WIRE RANGE
1) OVERVIEW
The VI2F-PIT4B is an indoor audio/video station of the AVE DOMINA system 2-wire video-intercom system V44EASY. The functions and characteristics are as follows:
Audio/Video/Buttons:
• 4.3" horizontal display; • Hands-free; • Touch buttons: gate opening, silencing, camera display;
Warnings:
• Active ringtone silencing; • Door open;
Video intercom functions:
• Answering a call; • Display of analogue cameras through a special VI2F-CAM interface; • Management of auxiliary outside door bell • Management of 3 gates, two on board the outdoor station and
one optional on auxiliary relay VI2F-RELAY; • Intercommunication between appliances of the same apartment or of other apartments
2) DECLARATION OF CONFORMITY
The VI2F-PIT4B device complies with the following standards:
• EN 62820-1-1:2016 Building intercom systems Part 1-1: System Requirements – General. Grade 2;
It also complies with the following directives and regulations:
• RoHS Directive 2011/65/EU;
• REACh Regulation (EC) No. 1907/2006;
• EMC 2014/30/EU
3) INSTALLATION, POSITIONING AND FIXING
The device should be installed at a height of 1.5m from the ground. Screw the screws supplied to secure the support bracket to the 3-module box, previously fixed to the wall in a vertical position.
Once wiring operations have been completed, align the slots in the back of the monitor with the bracket hooks (1) and slide the device slightly downwards (2). The AVE video-intercom system complies
with the strictest product standards both as regards performance and safety requirements and compliance with the relevant environmental tests. It also contains advanced video surveillance functions
(which can be activated during installation of the system) that may be subject to Regulation 679/2016 ("GDPR") and the General Provision of the Video surveillance authority of 8 April 2010. Since these
indications establish specific obligations for the protection of privacy, we draw attention to the fact that the installation is carried out according to the current laws and legislative decrees on "privacy".
4) CONNECTIONS
The meaning of the connection terminals and dip-switches located on the rear of the device is illustrated here below (see Fig. 3):
 
2-Wire BUS
Polarized 2-pole removable male
connector
• Terminal 1: BUS A
• Terminal 2: BUS B
5) ADDRESSING
Within 60 s from power-on, press the button
7" RAL 7023 7"
7" RAL 7023
1. Address setting: press briefly
increase it quickly (from 001 to 200). Press
2. Saving the address: press briefly
the stand-by mode. Press briefly
6) MEANING OF BUTTONS
MICROPHONE
DISPLAY
4,3" RAL 7023 4,3" RAL 7023
4,3" RAL 7023
MONITOR:
opens the audio-video connection
with outdoor station #1; press the
button again to display the other
outdoor stations or any cameras.
active, press the button to unlock the
 
2-pole dip-switch
• SW1-1 Device Master/Slave Setting: Move to (M) or to (S) to assign the Master or
Slave role, respectively
• SW1-2 Impedance matching: turn to ON (RC) when the station is the last in a series.
Otherwise, leave to OFF. It must be set to ON even if the station is connected to the
VI2F-PIDIST indoor distributor.
for 3 s; after a long "Beep" the interface for setting address
RAL 7023 7" RAL 7023 7" RAL 7023
(UP), the displayed address will be incremented by 1. Press and hold the address to
(DOWN) to decrease it in the same way.
(OK); the current address number will be assigned and saved and the device will enter
to exit without saving the displayed address number.
4,3" RAL 7023 4,3" RAL 7023
LOUDSPEAKER
CONCIERGE CALL (if any) / LEFT
SCROLL: no function in Stand-by. Opening
an indoor station becomes a
concierge when it is assigned the
address 200. When the call is
auxiliary relay (optional).
LOCK / OK:
press briefly to activate/deactivate the ringtone
the gates of the currently silencing (the LED will turn red when the
operating displayed station. ringtone is active). Press and hold to propagate
Short press: opening gate #1 the activation/deactivation of the silencing to any
Press > 3 s: opening gate #2 other slave stations in the same apartment.
Input for the outside door bell button
2-pole polarized male connector (complete with 10 cm
cable)
• Terminal 1: GND
• Terminal 2: door bell input
Note: use a potential-free normally open button
ADDRESS : 001
DOWN
Address setting interface
LED
Green ON:
Device powered
Flashing green:
Call in progress
Red ON:
Silencing active
Flashing red/green:
Door open (see par. 6)
SILENCING / RIGHT SCROLL:
 
OK UP BACK
CALL:
press to access the
communication interface
and to answer an incoming
call.