tau K580M Guía Para La Instalación página 16

HOW TO SET THE SOFT-STOP (software version 2.03 or later)
1_ Disconnect the K580M controller from the electrical power supply,
limit switch position and set the dip-switch n°9 to OFF;
2_ Connect the K580M controller to the power supply, wait a few seconds until the LED DL8 remains
always on and move the dip-switch n°9 to ON;
3_ Let the gate make a complete opening manoeuvre. During such manoeuvre, the card will save the
time needed far the opening and will not perform the soft-stop;
4_ Set the required soft-stop through the RALL trimmer. The soft-stop function will be correctly set up.
ADVANCED FUNCTIONS
Clock function: a timer can be connected to the open-close pushbutton in order to keep the gate
open at certain times during the day, after which it reverts to automatic closing.
Note: the gate remains open as long as the Op/Cl input continues to be activated.
"Open only" function: setting dip 1 and dip 4 to ON, the Op/Cl input will function solely as an open-
ing command and the gate will close only after the automatic closure time has elapsed.
"Gate contact open" function: setting dip 7 and dip 8 to OFF, the 2nd ch radio (terminals 18 - 19)
will act as a no-voltage contact which indicates when the gate is open. This function can be used to
connect "ZONE LIGHTING" or as a gate open signal.
433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 30 dip-switches (TXD2, TXD4, BUG2, BUG4, K-
SLIM, K-SLIM-C, T-4, T-4C) or rolling codes (BUG2R, BUG4R, K-SLIM-RP, T-4RP) which can be set
on the two channels as required.
The first channel directly commands the control board for opening the automatic device; the second
channel commands a relay for a N.O. no-voltage output contact (terminals 18 and 19, max. 24 Vac,
1 A).
The learning mode (dip-switch or rolling code) is determined by the first radio control device and re-
mains unchanged until all the codes have been cancelled.
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
P1 = OPEN/CLOSE
P2 = 2nd channel
1_ press button P1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ LED DL8 turns off to indicate that the code learning mode has been activated (if no code is en-
tered within 10 seconds, the board exits the programming mode);
3_ press the button of the relative radio control device;
4_ LED DL8 turns on again to indicate that the code has been memorised (if this does not happen,
wait 10 seconds and start again from point 1);
5_ to memorise codes to other radio control devices, repeat the procedure from point 1 up to a maxi-
mum of 30 transmitters;
6_ to memorise codes on the 2nd channel, repeat the procedure from point 1 using button P2 instead
of P1;
7_ to exit the learning mode without memorising a code, press button P1 or P2 briefly.
Note: If the maximum number of radio controls is reached (30), the LED DL8 will begin to flash
rapidly for about 3 seconds but without performing memorisation.
REMOTE PROGRAMMING BY MEANS OF T-4RP and K-SLIM-RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new
version of transmitters T-4RP and K-SLIM-RP (V 4.X), that is without pressing the receiver's program-
ming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the pro-
cedure of remote programming of the new transmitters. Follow the procedure written on the instruc-
tions of the transmitter T-4RP and K-SLIM-RP (V 4.X).
16 K580M
place the gate in the closing