Publicidad
Idiomas disponibles
Idiomas disponibles
15
Wire diameter (Genesis..Smart)
In synergy, allows selection of the wire diameter used
(mm).
16
Synergy (Genesis...Exclusive)
Lets you select a preset welding program (synergy) by
choosing a few simple settings:
- wire type
- gas type
- wire diameter
G3/4 Si1 CO 2
G3/4 Si1 Ar 18%CO 2
CrNi 19 9 Ar 2%CO 2
AlMg5 Ar
AlSi5 Ar
Al99,5 Ar
CuAl8 Ar
CuSi3 Ar
Basic FCW Ar 18%CO 2
Rutil FCW Ar 18%CO 2
Metal FCW Ar 18%CO 2
CrNi 19 9 FCW Ar 18%CO 2
17
Programs (Genesis..Exclusive)
Allows the storage and management of 64 welding pro-
grams which can be personalised by the operator.
Program storage
Enter the "program storage" menu by pressing button
(17) for at least 1 second.
Select the required program (or the empty memory) by
rotating the encoder.
Confirm the operation by pressing button-encoder (9).
Program retrieval
Retrieve the 1st program available by pressing button (17).
Select the required program by pressing button (17).
Select the required program by rotating the encoder.
Only the memories location occupied by a program
are retrieved, while the empty ones are automatically
skipped.
18
Wire feed
Allows the manual wire feed without gas flow and with-
out the wire live.
Allows the insertion of the wire into the torch sheath
during the welding preparation phases.
19
Gas test button
Allows the gas circuit to be cleansed of impurities and
the carrying out of the appropriate preliminary gas pres-
sure and flow adjustments, without power on.
20
Inductance
Allows electronic regulation of the series inductance of
the welding circuit.
Low inductance = reactive arc (more spatter).
High inductance = less reactive arc (less spatter).
Minimum -30, Maximum +30, Default syn
38
Ø (mm)
0.6
0.8
1.0
1.2
1
2
3
6
7
8
11
12
13
14
/
17
18
19
/
22
23
24
/
27
28
29
/
32
33
34
/
37
38
39
/
/
/
42
/
/
/
46
/
/
/
50
/
/
/
54
21
Soft start (Genesis...Classic)
Permits adjustment of the wire feed speed in the phases
prior to arc striking.
Given as a % of the wire speed set.
Permits striking at reduced speed, therefore softer and
with less spatter.
Minimum 10%, Maximum 100%, Default 50%
Burn back (Genesis...Classic)
Permits adjustment of the wire burn time, preventing
sticking at the end of welding.
Permits adjustment of the length.
Permits adjustment of the length of the piece of wire
outside the torch.
Minimum -2.00, Maximum +2.00, Default syn
3.3 Set up
Permits set up and adjustment of a series of additional parameters
for improved and more accurate control of the welding system.
The parameters present at set up are organised in relation to the
4
welding process selected and have a numerical code.
9
Entry to set up: by pressing the encoder key for 5 sec.
Selection and adjustment of the required parameter: by
turning the encoder until displaying the numerical code relating
to that parameter. If the encoder key is pressed at this point,
the value set for the parameter selected can be displayed and
adjusted.
Exit from set up: to quit the "adjustment" section, press the
encoder again.
To exit the set up, go to parameter "O" (save and quit) and press
the encoder.
3.3.1 List of set up parameters (MMA)
0
Save and quit
Allows you to save the changes and exit the set up.
1
Reset
Allows you to reset all the parameters to the default
values.
3
Hot start
Allows adjustment of the hot start value in MMA.
Permits an adjustable hot start in the arc striking phases,
facilitating the start operations.
Parameter set as a percentage (%) of the welding current.
Minimum Off, Maximum 500%, Default 80%
7
Welding current
Permits adjustment of the welding current.
Parameter set in Amps (A).
Minimum 3A, Maximum Imax, Default 100A
8
Arc force
Allows adjustment of the Arc force value in MMA.
Permits an adjustable energetic dynamic response in
welding, facilitating the welder's operations.
Increasing the value of the arc force to reduce the risks
of sticking of the electrode.
Parameter set as a percentage (%) of the welding current.
Minimum Off, Maximum 500%, Default 30%
204
Dynamic power control (DPC)
It enables the desired V/I characteristic to be selected.
I = C Constant current
The increase or reduction in arc length has no effect on
the welding current required.
Basic, Rutile, Acid, Steel, Cast iron
Publicidad
