Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT: To avoid getting an electric
shock, please observe the following rules. Once
you touch the electrical parts, they can cause a
lethal shock or burns:
1. Do not touch the electrical parts.
2. Allow the electrician to connect the welder
to earth in accordance with the aforementioned
regulations.
3. When installing and repairing the machine,
you must remove the power from the distribu-
tion box and operate after 5 minutes.
4. Do not use the cable if the insulated protec-
tive cover is damaged and the conductor is ex-
posed.
5. Secure the insulation of the cable seal.
6. Do not use the soldering iron without insulat-
ing coating.
7. Use dry insulating gloves
8. Please use a secure network when operating
in a high place
9. Maintenance and repair the welder regularly,
only use it in good operating conditions.
10. Please turn off all input power at the end of
the operation.
11. Use a shockproof device when using the ma-
chine in narrow or high places.
IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.
TOOL USE AND CARE
Do not force the power tool. Use the correct
tool for the application. The correct tool will do
the job better and more safely at the rate that it
was designed to work at.
Do not use tools if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the plug from the power source be-
fore making any adjustments, changing acces-
sories or storing the tool. This preventive safety
measures reduce the risk of accidental starting
of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
10
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in work pieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
SERVICE: Tool service must be performed only
by qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
SPECIFIC SAFETY RULES FOR
INVERTER ARC WELDER
To avoid accidents such as fire, explosions and
cracks, please obey the following rules:
1. Do not place flammable materials near the
site to be welded.
2. Do not weld near a source of flammable gas.
3. Do not place the tool when it is hot near a
flammable material.
4. The parts of the cable seal must be completely
insulated.
5. When welding either on the floor or on the
wall, clean or remove the flammable material
on the back.
6. The connection of the cable to the side of
the machine must be close to the piece to be
welded.
7. Do not weld near a gas pipe, sealed contain-
ers or other similar container.
8. Keep an extinguisher near the site when
welding.
DURING THE OPERATION
NOTICE: Contact with rotating parts can
cause injury, please observe the following regu-
lations:
Publicidad
