Publicidad
Idiomas disponibles
Idiomas disponibles
Audio settings
The menu items vary according to the source. Some of the menu items become
unavailable when the volume is muted.
Menu Item
Description
[Graphic EQ]
Select or customise the equaliser curve.
[S.Bass] [Powerful]
Select a curve that you want to use as the basis of customising
[Natural] [Vocal] [Flat]
then touch the frequency that you want to adjust.
[Custom1] [Custom2]
TIPS
• If you make adjustments when a curve [S.Bass], [Powerful],
[Natural], [Vocal], or [Flat] is selected, the equaliser curve settings
will be changed to [Custom1] mandatorily.
• If you make adjustments when the [Custom2] curve is selected
for example, the [Custom2] curve will be updated.
• [Custom1] and [Custom2] curves can be created common to all sources.
[Fader/Balance]
Touch
[Front] and [Rear] to [0] when using a dual speaker system.
Touch
TIP
You can also set the value by dragging the point on the displayed table.
NOTE
Only the fader can be adjusted when [Rear] is selected as the
speaker mode.
[Source Level Adjuster]
Adjust the volume level of each source to prevent radical
[-4] to [+4]
changes in volume when switching between sources other
than FM.
Touch
comparing the FM tuner volume level with the level of the
source.
TIP
If you directly touch the area where the cursor can be moved, the
SLA (source level adjustment) setting will be changed to the value
of the touched point.
NOTES
• Settings are based on the FM tuner volume level, which remains
unchanged.
• This function is not available when the FM tuner is selected as
the AV source.
[Subwoofer]
Select enable or disable subwoofer output from this
[On] [Off]
product.
or
to adjust the front/rear speaker balance. Set
or
to adjust the left/right speaker balance.
or
to adjust the source volume after
Menu Item
Description
[Speaker Level]
Adjust the speaker output level of the listening position.
1
[Front Left] [Front Right]
Touch
[Rear Left] [Rear Right]
select the output speaker.
2
[Subwoofer] [Listening
Touch
Position]
level.
NOTE
For rear speaker, this function is available only when [Rear] is
selected in [Rear Speaker Output].
[Crossover]
Select a speaker unit (filter) to adjust the HPF or LPF cut-off
frequency and the slope for each speaker unit (page 21).
[Subwoofer Settings]
Select the subwoofer phase, LPF cut-off frequency and the
slope (page 21).
[Listening Position]
Select a listening position that you want to make as the
[Off] [Front-L] [Front-R]
centre of sound effects.
[Front] [All]
[Time Alignment]
Select or customise the time alignment settings to reflect
[Front Left] [Front Right]
the distance between the listener's position and each
[Rear Left] [Rear Right]
speaker. You need to measure the distance between the
[Subwoofer] [Listening
head of the listener and each speaker unit.
1
Position]
Touch
select the alignment speaker.
2
Touch
selected speaker and listening position.
NOTE
This function is available only when the listening position setting
is set to [Front Left] or [Front Right].
[Bass Boost]
Adjust the bass boost level.
[0] to [+6]
[Rear Speaker Output]
Select the rear speaker output.
[Rear] [Subwoofer]
NOTE
This function is available when the source is off.
[Loudness]
Compensates for deficiencies in the low-frequency and
[Off] [Low] [Mid] [High]
high-frequency ranges at low volume.
NOTE
This function is not available while you make or receive a call using
the hands-free function.
Adjusting the cutoff frequency value
You can adjust the cutoff frequency value of each speaker.
or
to select the listening position then
or
to adjust the selected speaker output
or
to select the listening position then
or
to input the distance between the
21
En
Publicidad
