Descargar Imprimir esta página

VONROC MS502AC Traducción Del Manual Original página 11

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 61
• When sawing curved or round workpieces, these
must be especially secured against slipping. At
the cutting line, there should be no gap between
the workpiece, fence and saw table. If necessary,
you will need to manufacture special fixtures.
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable for
the power rating of the machine with a minimum
thickness of 1.5 mm
. If you use an extension
2
cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
This tool is intended as a stationary machine for
making straight lengthways and crossways cuts in
wood with and against the grain. It is possible to
cut mitre angles of -45° to +45° and bevel angles of
-0° to +45°. The power tool with the fitted sawbla-
de is designed with sufficient capacity for sawing
hardwood and softwood as well as chipboard and
fibreboard. The sawblade is not designed for cut-
ting firewood. Do not use the saw to cut materials
other than those specified described in manual.
TECHNICAL SPECIFICATIONS
Model No.
Voltage
Frequency
Power input
No load speed
Mitre angles
Bevel angles
Sawblade specifications:
Diameter
Base blade thickness
Width of cut
Bore diameter
Number of teeth
WWW.VONROC.COM
Saw capacity (height x width):
Minimum workpiece dimensions 3 x 10 mm
Laser specifications:
Weight
Lpa (sound pressure level)
Lwa (sound power level)
Vibration value
*
*
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardised test given in EN 60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned
-
MS502AC
-
220-240V~
50 Hz
Protect yourself against the effects of vibration by
2000W S1, 2200W
maintaining the tool and its accessories, keeping
S6 25%
your hands warm, and organizing your work patterns
4500/min
DESCRIPTION
-45° <> +45°
The numbers in the text refer to the diagrams on
-45° <> 0° to the left,
page 2-6.
single bevel
1. Lock-off button
Ø 254 mm
2. Handle
1.6 mm
3. On/off switch
2.8 mm
4. Protective guard
Ø 30 mm
5. Retracting protective guard
60T
6. Saw blade
Mitre 0° - Bevel 0°
Mitre 0° - Bevel 45°
Mitre 45° - Bevel 0°
Mitre 45° - Bevel 45
Class
Wavelength
Output
S1, continuous duty operation mode.
S6, continuous operation periodic duty. Identi-
cal duty cycles with a period at load followed by
a period at no load. Running time 10 minutes;
duty cycle is 25% of the running time.
using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
the times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
EN
90 x 340 mm
45 x 340 mm
90 x 240 mm
45 x 240 mm
2
650 nm
< 1 mW
14.3 kg
101.6 +3 dB(A)
114.6 +3 dB(A)
<2.5 m/s
2
11

Publicidad

loading