Descargar Imprimir esta página

camry CR7422 Manual De Uso página 8

Ocultar thumbs Ver también para CR7422:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
15. The device should be turned off every time you put it down.
16. Do not use the device near water, for example: in the shower, in the bathtub or above the
basin with water.
17. If the device uses a power supply, do not cover it, as it could lead to a dangerous increase
in temperature and damage to the device. Always, first insert the plug into the power socket in
the device and then the power supply to the mains socket.
18. Do not use the bed sheet in folded condition. Do not put pins, needles and other metal
objects in the sheet.
19. Do not use the sheet if it is wet or damp. Leave the sheet hung loosely in a ventilated
area until it is completely dry.
20. Do not put the power cord on a warmed sheet. Do not fold the equipment when it is
placed on top during storage. Check the equipment periodically for signs of wear or damage.
If such signs or equipment are used improperly, please contact your supplier before
continuing to use it.
21. Store in a dry place. Never put heavy objects on the sheet.
22. Never go to sleep with the electric sheet turned on. Unplug the power plug from the outlet.
23. Never cover the controller.
24. Before switching on the electric sheet, make sure that it is evenly distributed, there are no
kinks or folds.
25.
Product can be washed in the washing machine in 30°C temperature
power cord and controller before washing. Switch or controller - the regulator must not be wet
during washing, and during drying the cord must be in a horizontal position to ensure that the
water does not flow into the switch or controller - the regulator.
26. Do not iron the electric sheet!
27. This equipment is not intended for medical use in hospitals.
28. The device should cool down before storage.
29. The device may be used only with the types of removable elements specified in the
equipment marking.
30. Do not use the device on adjustable beds or if the device is used on an adjustable bed,
check that the blanket and cord cannot get stuck or corrugated, eg on hinges.
31. The device is equipped with a fuse protecting against overheating, which should not work
when used in accordance with the intended use of the equipment. If the fuse trips, the device
will stop working, the equipment must be returned to the manufacturer or its representative
for repair.
Product: Electric blanket underlay CR7416 / CR7417 / CR7423 / CR7424 / CR7421 / CR7422
BEFORE FIRST USE
1.The product needs to be unfolded and laid flat before switching on.
2.Fix the product according to instruction in chapter: Fitting your product on the bed.
3.We recommend that you switch your product to the maximum setting for two to three hours before bedtime then reduce to your desired
heat setting 15 minutes before getting into bed. You must switch OFF prior to sleeping.
Fitting your product on the bed
1. Place the product onto the mattress with the controller (or two) at the HEAD END but towards the foot end of the bed.
2. The control switches should be below the normal head's sleeping position.
3. Unroll the tie tapes and pass the tapes under the bed as shown in the diagrams (Fig.1-6).
4. Ensure the heating wires do not extend under pillows or hang over the sides. Pass the middle tie tape under the mattress and through the
middle loop on the opposite side (Fig.1). Pass end of tape under the corresponding bottom corner of the mattress (Fig. 2) up through the
center loop of product (Fig. 3) and down under opposite corner of mattress and then through side loop on opposite side of the product (Fig
4).
5. Repeat this process at the other end (Fig. 5).
DESCRIPTION OF THE DEVICE - electronic controller
1. Temperature controller
3. Bed sheet / blanket / mat
5. Controller display
2. Power cord
4. Socket to disconnect the power cord before washing
6. Switch "ON/OFF"
8
. Disconnect the

Publicidad

loading

Este manual también es adecuado para:

Cr7421