Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Note:
• Rinse the filter grid with clean water and do not add
any detergent.
• Do not clean the filter grid with a brush or fingers.
• Allow the filter grid to air dry for at least 24 hours.
• Replace the filter grid every 3 to 6 months.
Cleaning the filter (clean regularly)
Wiping module (clean after each use)
1. Remove the cloth, empty the water tank.
2. Clean the cloth, dry both the water tank and the cloth.
Sensors (clean regularly)
Clean the sensors with a soft cloth as follows:
1. Clean the sensors along the wall to the right.
2. Three cliff sensors at the bottom of the appliance.
3. Infra-red anti-collision sensor in front of the appliance.
4. Protection against electric shock and docking station
contacts at the bottom of the appliances (turn off the
appliance during cleaning).
5. Docking station signal transmission area.
Cliff sensor
Charging
contact
TOF sensor
82
Sensors (clean every month)
LDS laser range-
finder
Anti-collision sensor
for radar sensor
Anti-collision
sensor
Infra-red
charging sensor
Signal
transmission area
Base charging
contacts
Battery
• The appliance is equipped with high-performance
lithium-ion batteries. To maintain battery performance,
keep the appliance charged every day.
• If the appliance is not used for a long time, turn it off
and store it properly. Charge it at least every 3 months
to prevent damage to the batteries due to excessive
discharge.
Firmware update
Use the mobile app to update the firmware. If new
firmware is detected, update as prompted. When
updating the firmware, the battery level should be ≥50 %,
so the appliance should be placed in the docking station.
VR3115
COMMON PROBLEMS
Problem
Problem
The robot cannot be
• If the battery is low, place the robot in the docking station and align it with the board
The robot cannot be
• If the battery is low, place the robot in the docking station and align it with the board
started
contacts, the appliance will start automatically (if the robot is completely off, it can
started
contacts, the appliance will start automatically (if the robot is completely o , it can
start automatically after a while).
start automatically after a while).
• Do not use the appliance if the ambient temperature is below 0 °C or above 50 °C.
• Do not use the appliance if the ambient temperature is below 0 °C or above 50 °C.
Use at 0-40 °C.
Use at 0-40 °C.
The robot cannot be
• Move the robot off the station, make sure the docking station indicator light turns
The robot cannot be
• Move the robot o the station, make sure the docking station indicator light turns
charged
on, and make sure both ends of the docking station power adapter are properly
charged
on, and make sure both ends of the docking station power adapter are properly
connected.
connected.
• In case of poor contact, clean the docking station contact points and charging
• In case of poor contact, clean the docking station contact points and charging
contacts on the robot or turn the side brush to the side.
contacts on the robot or turn the side brush to the side.
The robot cannot be
The robot is too far from the docking station, place it near the docking station and try
The robot cannot be
The robot is too far from the docking station, place it near the docking station and try
recharged
again.
recharged
again.
Abnormal behaviour
Turn off the robot and restart it.
Abnormal behaviour
Restart the robot, the restart is done by holding the power and recharge button for
10-15s, the appliance flashes red and then switches o , after 30s the appliance can be
Unusual noise is heard
The main brush, side brush or wheel may be wrapped with foreign objects, turn off the
switched on again.
during use
robot and remove foreign objects.
Unusual noise is heard
The main brush, side brush or wheel may be wrapped with foreign objects, turn o the
Cleaning ability is
• The dust container is full. Clean it.
during use
robot and remove foreign objects.
reduced or dust is
• The filter grid is clogged. Clean or replace.
• The main brush is wrapped with foreign objects, clean it.
dropping from the
• The dust container is full. Clean it.
Cleaning ability is
appliance
reduced or dust is
• The filter grid is clogged. Clean or replace.
dropping from the
• The main brush is wrapped with foreign objects, clean it.
Wi-Fi cannot be
• The Wi-Fi signal is bad. Check that the correct Wi-Fi coverage is available.
appliance
connected
• Wi-Fi is connected in an unusual way. Reset Wi-Fi, download the latest app, and try
connecting again.
Wi-Fi cannot be
• The Wi-Fi signal is bad. Check that the correct Wi-Fi coverage is available.
• The password is entered incorrectly.
• Wi-Fi is connected in an unusual way. Reset Wi-Fi, download the latest app, and try
connected
• There is a router for the 5G frequency band, the robotic vacuum cleaner is equipped
connecting again.
only for the 2.4G frequency band.
• The password is entered incorrectly.
• There is a router for the 5G frequency band, the robotic vacuum cleaner is equipped
The planned cleaning did
If the battery level is low, planned cleaning can only be started if the battery level is at
only for the 2.4G frequency band.
not take place
least 30 %.
The planned cleaning did
If the battery level is low, planned cleaning can only be started if the battery level is at
Does the robot consume
The robot consumes a small amount of power when it is permanently placed in the
not take place
least 30 %.
power when it is always
docking station, allowing the best battery performance.
placed in the docking
Does the robot consume
The robot consumes a small amount of power when it is permanently placed in the
station?
power when it is always
docking station, allowing the best battery performance.
placed in the docking
Do I need to charge the
The lithium battery can be used immediately after charging and has no memory effect.
station?
robot three times for
16 hours the first time?
Do I need to charge the
The lithium battery can be used immediately after charging and has no memory e ect.
robot three times for
VR3115
EN
Remedy
Remedy
83
Publicidad
