Tabla de contenido
Publicidad
When attaching the armrest, keep an eye on
the button, because it must be in front of the
armrest and not behind, as shown.
Attach the armrests to the chassis as shown.
18 HOOD: The hood comes with a loop for
hanging your child's favorite toy (fig_a) and a
see-through window for observing your child
(fig_b), which can be lifted and fastened. You
can detach the Velcro, roll up the back of the
hood and fasten it at the top with the rubber
band to allow greater ventilation during use
with the backrest down (fig_c). The hood may
be pulled forward into several positions (fig_d).
19 ADJUSTING THE BACKREST: to lower the
backrest, press the clip and the backrest will
move down to the desired position.
To raise the backrest, press the clip and lift
the backrest to the desired height.
20 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
21 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
22 Before adjusting the height of the safety
harness remove the shoulder pads (fig_a). To
adjust the height, slip the belts through the
eyelet in the fabric (fig_b) and position them
in the most suitable eyelet.
23 FOLDING UP: To fold up the stroller, we
recommend ensuring the front wheels swivel,
closing the hood, removing the car seat when
fastened.
- Align the handlebar and frame as shown in
the figure (fig_a).
- Push the inside folding handle downwards
(fig_b), checking that the fastener has been
released.
- Pull both handles towards you (fig_c), and
whilst maintaining the same grip, lift the
frame (fig_d).
24 Allow the handlebar to fall in on itself until
fully folded (fig_e).
The frame is folded correctly when the side
fastener automatically locks (fig_f). Otherwise,
gently press down on the frame (fig_g).
The stroller is free-standing when folded.
25 For greater compactness, it is possible to
remove the wheels.
To remove the rear wheels: pull the pivot
outwards and remove the wheel as shown in
the figure (fig_a).
To remove the front wheels: press the tab as
shown, and remove the wheel (fig_b).
TRANSPORT: the stroller can be carried
comfortably locking the front wheels and
grasping the main handle (fig_c).
26 REMOVABLE ITEMS: to remove the hood, take
the elastic off from the buttons on the inside
of the handlebar (fig_a), detach the press
studs the sides of the chassis (fig_b), detach
the Velcro strip from the backrest (fig_c) and
remove the attachments of the hood from
their positions on the chassis (fig_d).
27 To remove the seat fabric, press in the holes
on the inside of the chassis (fig_a); remove,
from the side of the seat, the rigid flap of the
chassis fabric ((fig_b), unfasten the elastic
of the net from the side buttons inside the
handlebar (fig_c) and unfasten the elastics
from the buttons inside the chassis (fig_d).
28 Slip the cover off the footrest from the front
(fig_a), pull the crotch strap out from below
the seat (fig_b), unhook the rubber band
from the seat's side hook (fig_c), unscrew the
waist strap (fig_d) and remove the cover from
the backrest (fig_e).
GANCIOMATIC SYSTEM
The Ganciomatic System is the quick, practical
system that allows you to fasten the Primo
Viaggio 4•35 / Primo Viaggio 4•35 Nido car seat
(sold separately) onto the stroller using the
Ganciomatic hooks.
29 GANCIOMATIC HOOKS ON THE STROLLER:
to lift the stroller's Ganciomatic hooks, pull
back the fabric at the corners of the seat.
Pull the frame's side levers outwards (fig_a)
and turn the Ganciomatic hooks upwards.
_ To lower the hooks, proceed in the opposite
order.
GANCIOMATIC FASTENING
30 Z3 + Primo Viaggio 4•35/ Primo Viaggio 4•35
Nido
To mount the car seat on the stroller or
chassis, you must:
_ Engage the stroller's brake;
_ Lift the stroller's Ganciomatic hooks;
_ Pull the front bar out to the second position
(fig_a).
_ Fully lower the backrest, if in place.
_ Place the car seat, facing mom, on the
Ganciomatic hooks and push it down until it
clicks into place.
_ Once the seat is mounted, lift the backrest - if
in place - to the maximum height (fig_b).
_ See the instruction manual to release the car
seat from the stroller.
SERIAL NUMBERS
31 Information about the production date can
be found on the Z3 .
_ The product name, production date and serial
number of the chassis.
This information is required for any complaints.
- 16 -
Publicidad
Tabla de contenido
