Technical Specifications - Metabo BFE 9-20 Instrucciones De Manejo

6.5 Sanding procedure
Switch the machine on first before mounting it on
the workpiece.
Place the machine on the material such that the
sanding belt is parallel to the surface of the
workpiece.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
6.6 Replacing the sanding attachment
See illustration C, page 2.
- Removing the sanding belt (see Section 6.3).
- Remove screw (2), and remove sanding
attachment (1).
- Attach the other sanding attachment as shown
(ensure that the nose at the end of the sanding
attachment is pointing in the direction of the
tensioning arm, see illustration C).
- Secure with screw (2).
- Attaching the sanding belt (see Section 6.3).
- Adjusting the belt run (see Section 6.4).
7. Cleaning, Maintenance
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
8. Tips and Tricks
For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
9. Troubleshooting
- Overload protection: There is a MAJOR
reduction in load speed. The motor temperature
is too high! Allow the machine to run at idle speed
until it has cooled down.
- Overload protection: There is a SLIGHT
reduction in load speed. The machine is
overloaded. Reduce the load before continuing to
work.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
10. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model of your
power tool in order to select the correct accessory.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
12. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.

13. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
B = Sanding belt length
L
v = Belt speed in idling
0
P = Nominal power input
1
P = Power output
2
m = Weight without mains cable
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value
h
(sanding surfaces)
K = Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Problems, faults:
In individual cases, the speed may fluctuate
temporarily if the machine is exposed to extreme
external electromagnetic disturbances or the
electronic restart protection may respond. In this
case, switch the machine off and on again.
ENGLISH en
7