Technical Specification - Hallde RG-350 Instrucciones De Uso

REMOVING THE CUTTING TOOLS
Raise the pusher plate (1:A) and swing it out
to the left, or remove the feed hopper (4:C).
Turn the locking knob (1:B) anti-clockwise
and raise the feeder/lid (1:C).
Remove the cabbage screw (1:J) by turning
it clockwise by means of the spanner (1:K).
Remove the cutting tool/tools and the
ejector plate (1:D).
USING THE FEEDERS
The large feed compartment is used mainly
for bulk feeding of potatoes, onions, etc.
(2:A) and for cutting larger products such as
cabbage.
The large feed compartment is also used
when the material is to be cut in a definite
direction, such as tomatoes and lemons.
Place/stack the products as shown in the
figure (2:B).
The feed tube is used for cutting long
products such as cucumbers (2:C).
The feed hopper (4:C) is used for
continuous cutting of large quantities of
potatoes, etc.
CLEANING
Switch off the machine and remove the
power supply plug from the socket or open
the isolating switch.
Carefully clean the machine immediately
after use.
If you have used a dicing grid (3:G), leave it
in the machine, and use the brush (4:B) for
pushing out any product remaining in the
grid.
Remove the loose parts of the machine, wash
them and dry them thoroughly.
Never wash light metal items in the
dishwasher unless they are marked "diwash".
All accessories marked "diwash" can be
washed in the dishwasher.
All cutting tools can be washed in the
dishwasher.
Wipe the machine with a damp cloth.
Always wipe the knives of the cutting tools
dry after use.
Always store the cutting tools (3) on the
hangers (4:A) on the wall.
Never use sharp objects or a high-pressure
spray gun for cleaning.
Never spray water on the sides of the
machine.
CHECK EVERY WEEK
That the machine stops as soon as the pusher
plate (1:A) has been moved up and swung
out, and that it restarts when the pusher
plate has been swung in and lowered.
That the machine cannot be started with the
feeder/lid (1:C) removed and with the
pusher plate lowered.
Remove the plug from the power supply
socket and then check that the electric cable
is in good condition and is not cracked on
the outside.
If any of the two safety functions does not
perform as intended or if the electric cable is
cracked, get a specialist to attend to the
machine before connecting it back to the
power supply.
Check that the pusher plate shaft (1:I) has
been lubricated as necessary and runs
freely. If the shaft does not run freely, clean it
carefully and lubricate it with a few drops of
machine oil.
Check that the knives and shredder plates
are in good condition and are sharp.
TROUBLE-SHOOTING
FAULT: The machine cannot be started, or
stops while it is running and cannot be
restarted.
REMEDY: Check that the plug is securely
fitted into the power supply socket, or that
the isolating switch is closed. Check that the
feeder/lid (1:C), pusher plate (1:A) or the
feed hopper (4:C) is locked in the correct
position. Move down the pusher plate into
the feeder/lid. Check that the fuses in the
fuse box for the premises have not blown
and that they have the correct rating. Wait
for a few minutes and try to restart the
machine. If the machine still fails to run, call
a specialist.
FAULT: Low capacity or poor cutting results.
REMEDY: Make sure that you are using the
correct cutting tool or combination of
cuttings tools (3). Fit the cabbage screw
(1:J). Check that the knives and shredder
plates are in good condition and are sharp.
Press the food down loosely.
FAULT: The cutting tool (3) cannot be
removed.
REMEDY: Always use the ejector plate (1:D).
Use a thick leather glove or the like that the
knives of the cutting tool cannot cut through,
and turn the cutting tool clockwise to release
it.
FAULT: The cabbage screw (1:J) cannot be
removed.
REMEDY: Use the spanner (1:K) to unscrew
the cabbage screw clockwise.

TECHNICAL SPECIFICATION

MACHINE: Motor: 0.75 kW, 230 V, single-
phase, 50 Hz, or 400 V, 3-phase, 50 Hz,
with thermal motor protection. Transmission:
gears. Safety system: Four safety switches.
Degree of protection: IP44. Power supply
socket: Earthed, single-phase, 10 A, or 3-
phase, 16 A. Fuse in fuse box for the
premises: 10 A, slow-blow. Sound level LpA
(EN3 1201): 73 dBA.
TOOLS: Diameter: 215 mm. Speed: 360
rpm.
MATERIALS: Machine housing and feed
cylinder: Anodized or polished aluminium
alloy and/or stainless steel. Cutting tool
discs: Aluminium alloy. Cutting tool knives:
Knife steel of the highest quality.
NET WEIGHTS: Machine: 32 kg. Cutting
tools: About 1 kg on average.
STANDARDS: NSF STANDARD 8, EU
Machine Directive 89/392EEC .