Publicidad
CAUTION! This device is designed to operate indoors. The
design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is
always a small risk of injuries at work.
Explanation of used symbols
1. Attention! Take special precautions
2. WARNING Read the instruction manual
3. Wear protective gloves
4. Use personal protective equipment (safety goggles, ear
protectors)
5. Use protective clothing
6. Unplug the power cord before servicing or repair
7. Keep children away from tools
8. Protect the device against moisture
9. Second protection class
CONSTRUCTION AND USE
Polisher is a power tool driven by a single-phase commutator motor.
The tool is designed for dry buffing and polishing mainly lacquer
coated surfaces of wood, metal or plastic workpieces. Rotary speed
adjustment allows to obtain optimal working parameters depending
on used buffing and polishing accessories.
Range of use covers works in renovation and finishing tasks at
surface polishing, in particular for automotive and woodworking
applications.
The tool is designed for dry operation only. Do not use with
corundum discs.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Rear handle
2. Control panel
3. Gear casing
4. Spindle lock button
5. Fixing hole
6. Holding pad
7. Fixing screw
8. Additional D handle
9. Additional handle
10. Polishing wheel
11. Polishing pad
12. Buffing-polishing wheel
13. Polishing sponge
14. Switch
15. Display
16. Speed adjustment button -
17. Speed adjustment button +
* Differences may appear between the product and drawing.
EQUIPMENT AND ACCESSORIES
1. Polishing wheel
2. Additional handle
3. Holding pad
4. Fixing screw
5. Washer
6. Hexagonal key
7. Polishing pad
8. Polishing sponge
9. Cloth
PREPARATION FOR OPERATION
Disconnect the polisher from power supply network.
INSTALLATION OF HOLDING PAD
• Slide the holding pad (6) (fig. A) onto gear casing (3) from front
to back.
• Use the fixing screws (7) and screw them into the fixing holes (5)
on both sides of the gear to secure the installation (fig. B).
Front side of the holding pad (6) features recess for fingers at the
bottom to provide firm grip.
INSTALLATION OF ADDITIONAL D HANDLE
You can set up additional D handle in one of two positions: vertical
or horizontal (fig. D and E). Set up must be made before installation.
The handle bow features keys that lock inside the inner fixing frame.
• Slide the additional D handle (8) (fig. C) onto gear casing (3)
from front to back.
• Use the fixing screws (7) with washers and screw them into the
fixing holes (5) on both sides of the gear to secure the installation
(fig. D).
INSTALLATION OF ADDITIONAL HANDLE
You can install additional handle (9) (fig. F) either on left or right
side of the gear casing (3). It is recommended for use with
accessories exceeding 125 mm in diameter.
Screw the additional handle (9) (fig. F) into one of the installation
holes (5) in the gear casing (3).
INSTALLATION AND DEINSTALLATION OF POLISHING
WHEEL / BUFFING-POLISHING WHEEL
• Press the spindle lock button (4) and rotate the spindle until it
locks.
• Screw polishing wheel (10) (fig. G) onto spindle with right-hand
thread.
• Release the spindle lock button (4).
• You can remove the polishing wheel by following the installation
procedure in reverse sequence.
• Use the same procedure to install and remove buffing-polishing
wheel with hook and loop attachment (12) (fig. I).
• The spindle lock button (4) is only used to install and remove the
buffing-polishing wheel. It cannot be used as a brake-button when
the wheel is rotating. Otherwise the polisher may be damaged or
the user may be injured.
INSTALLATION OF BUFFING PAD
• Pull the polishing pad (11) (fig. H) over polishing wheel (10) (fig.
D), stretch it slightly.
• Secure by pulling the line (put ends of line into the polishing pad
so they don't get loose during operation).
11
- 2 pcs
- 2 pcs
- 1 pce
- 2 pcs
- 2 pcs
- 1 pce
- 1 pce
- 2 pce
- 1 pce
Publicidad
