Publicidad
Método de ensaio com laser (Modelo nº ECO1000RTU)
Nota: Este ensaio não verifica completamente o funcionamento do detector.
1. Alinhe o ponto vermelho intermitente produzido pelo feixe laser com o LED no
detector.
2. Desde que o detector não tenha atingido o limite de compensação de desvio, deve
entrar no modo alarme ao fim de alguns segundos e activar o alarme no painel de
controlo.
MANUTENÇÃO
1. Retire do sistema o detector que vai limpar.
2. Cuidadosamente liberte cada uma das patilhas que seguram a tampa em posição
e retire a tampa.
3. Aspire com cuidado a parte exterior da grelha sem a remover.
4. Retire cuidadosamente a grelha da câmara de detecção.
5. Utilize um aspirador e/ou ar comprimido limpo para remover o pó e a sujidade da
câmara de detecção e do interior do resguardo.
6. Volte a instalar o resguardo alinhando a seta deste com a seta da câmara de
detecção, deslizando o resguardo sobre a câmara e exercendo uma ligeira pressão
para o segurar em posição.
7. Voltar a instalar a tampa do detector. Alinhe o LED com a tampa e encaixe-a em
posição certificando-se de que todas as patilhas de fixação da tampa estão
presas correctamente.
8. Quando tiver limpo todos os detectores, ligue de novo a alimentação para o
circuito e ensaie o detector conforme descrito na secção ENSAIO acima.
AVISO – LIMITAÇÕES DOS DETECTORES DE FUMO
O detector de fumo só funciona quando estiver ligado a um painel de controlo
compatível e operacional.
Os detectores de fumo têm limitações de detecção. Não detectam fogos cujo
fumo não chegue até aos detectores e tipos diferentes de detectores responderão
de forma diferente aos vários tipos de fumo.
Os detectores de fumo não duram indefinidamente e recomendamos a sua
substituição ao fim de 10 anos.
INSTALLATION AND MAINTENANCE INSTRUCTIONS FOR
ECO1003ABLINK PHOTO-ELECTRONIC SMOKE DETECTOR
SPECIFICATIONS
EN
Supply Voltage:
Quiescent current:
Maximum alarm current 80mA (Limited by panel or base resistance)
Latching Alarm:
WARNING - Detector characteristics may vary from other manufacturer products.
Check compatibility with panel supplier for any limitations. eg: maximum quantity
of devices per circuit.
BASE MOUNTING AND WIRING INSTRUCTIONS
See figure 1 for terminal connections. Detector LED position marked by diode symbol
and arrow on base wall (See fig 1 *)
Notes: Do not loop wire under terminals: Break the wire run to ensure supervision of
connections.
All wiring must conform to applicable local and national codes and regulations.
Each ECO1000 base is fitted with a shorting spring to connect across terminals 1 and
2 to permit loop wiring to be checked before installation of detector heads. This spring
automatically disengages when the detector is fitted into the base.
IMPORTANT - This detector is not compatible with the ECO1000BREL24L relay
base.
WARNING - Remove power from detector monitoring circuits before installing
detectors.
DETECTOR INSTALLATION
1. Place the detector into the base and rotate clockwise until the detector drops into
place. Continue rotating clockwise until the slot in the detector cover lines up with
the lines moulded in the base (See fig 2 **)
2. After all detectors have been installed, apply power to the detector monitoring
circuits.
3. Test the detector as described under TESTING.
Tamper-Resistance
The removal of the small plastic tab on the base indicated in fig. 2 prevents the removal
of the detector head without a tool.
CAUTION - Dust covers must be removed before the system can be made opera-
tional.
TESTING
Smoke Method
1. Using a test smoke from an approved manufacturer such as No Climb Products Ltd,
apply in accordance with the suppliers instructions
2. The red LED on the detector should latch into alarm within 40 seconds, and the
control panel should activate into alarm.
Laser Test Tool Method (Model No. ECO1000RTU)
Note: This method does not carry out a complete functional test of the detector.
1. Align the flashing red spot produced by the laser beam with the LED on the detector.
2. Provided the detector has not reached its drift compensation limit, it should latch
into alarm within a few seconds, and the control panel should activate into alarm.
MAINTENANCE
1. Remove the detector to be cleaned from the system.
2. Gently release each of the cover removal tabs that secure the cover in place and
remove the detector cover.
. Vacuum the outside of the screen carefully without removing it.
3
4. Carefully remove the screen from the sensing chamber.
5. Use a vacuum cleaner and/or clean, compressed air to remove dust and debris from
the sensing chamber and the inside of the screen.
LA700-02-01
8 - 30VDC
45µA Typical, at 24VDC, 25°C
Reset by momentary power interruption.
Pittway Tecnologica Srl, Via Caboto 19/3, 34147 Trieste, Italy
6. Re-install the screen by aligning the arrow moulded on it with the arrow on the
sensing chamber, sliding the screen over the chamber and applying gentle pressure
to secure it in place.
7. Reinstall the detector cover. Align the LED with the cover assembly and snap the
cover into place, ensuring that all the cover removal tabs are correctly engaged.
8. When all the detectors have been cleaned, restore power to the circuit and test the
detector as described in TESTING above.
WARNING - LIMITATIONS OF SMOKE DETECTORS
Smoke detector will only work when connected to a functioning, compatible control
panel.
Smoke detectors have sensing limitations. They will not sense fires where smoke
does not reach the sensor, and different types of detector will respond differently to
various smoke types.
Smoke detectors cannot last forever, and we recommended replacement after 10
years.
0832-CPD-1550 10
EN54-7: 2000 + A1: 2002 + A2: 2006
Pittway Tecnologica Srl, Via Caboto
19/3, 34147 Trieste, Italy
I56-3745-000
Publicidad
