Tabla de contenido
Publicidad
Il triangolo isoscele con punto esclamativo avverte di importanti segnalazioni relative all'uso e alla manutenzione.
ATTENZIONE: ELEVATI LIVELLI SONORI NEI PRODOTTI AUDIO!
Questo dispositivo è destinato a uso professionale. Di conseguenza, se viene destinato ad un uso commerciale, sarà soggetto alle
norme e ai regolamenti dell'Associazione per la prevenzione di infortuni del rispettivo settore professionale. In qualità di produttore,
Adam Hall è tenuto per legge a informare espressamente gli utenti degli eventuali rischi per la salute.
Danni all'udito provocati da un'esposizione prolungata a un livello SPL elevato: dall'utilizzo di questo prodotto si possono generare elevati livelli di
pressione sonora (SPL) che possono provocare danni irreparabili all'udito di artisti, collaboratori e spettatori. Evitare l'esposizione prolungata a livelli
sonori elevati, superiori a 90 dB.
Per evitare possibili danni all'udito, evitare l'ascolto ad un volume elevato per periodi prolungati.
L'esposizione al volume elevato può causare danni all'udito anche se è di breve durata. Mantenere sempre il volume ad un livello
gradevole.
OPERATING INSTRUCTIONS / HINWEISE ZUM BETRIEB / CONSEILS D' UTILISATION /
INTRODUCCIÓN / WPROWADZENIE / INTRODUZIONE
EN
Passive Speakers
SAT42G2(W) and SAT62G2(W)
Up to four SAT42G2(W) or SAT62G2(W) speakers per power amplifier output can be operated in parallel at 4 ohms. The speaker signal is simply looped
through to the next speaker via the connector panel on the rear.
SAT242G2(W) , SAT442G2(W) and SAT82G2(W)
Up to two SAT42G2(W) , SAT442G2(W) or SAT62G2(W) speakers per power amplifier output can be operated in parallel at 4 ohms. The speaker signal
is simply looped through to the next speaker via the connector panel on the rear.
SUB88 in conjunction with SAT42G2(W), SAT62G2(W), SAT242G2(W) or SAT82G2(W)
Connect the speaker cables from the power amplifier (Output Left and Right) to the Input Left and Right
connectors of the subwoofer. Afterwards, connect the SAT Series speakers to the Output Left and Right connectors of the subwoofer. Up to two
SAT42G2(W) or SAT62G2(W) speakers per subwoofer output (Output Left and Right) can be operated in parallel at 4 ohms. One SAT242G2(W) ,
SAT442G2(W) or SAT82G2(W) speaker per subwoofer output (Output Left and Right) can be operated in this configuration at 4 ohms. We recommend
using speaker cable with a conductor cross-section of at least 2 x 1.5 mm².
Active Speakers
It is advisable to always turn on active speakers last and turn them off first in order to avoid the switch-on noises caused by connected mixers, etc. If
multiple active speakers areconnected one after the other in series (SAT62AG2), then they should always be switched on in the order in which they are
connected and switched off in reverse order.
Turn the active speakers off before you connect them. They can be connected both via 6.3 mm TRS plugs (balanced three-pole / unbalanced two-pole)
as well as balanced three-pole XLR plugs. Once you have connected all of the necessary cables and set the volume (MAIN LEVEL) of the active speaker
to minimum, you can switch on the audio source (e.g., mixer). Afterwards you can also switch on the active speakers. Start an audio signal and now
turn the MAIN LEVEL knob clockwise until the desired volume is attained. Carry out these steps with all connected active speakers. On the following
pages of this user manual, you will find a summary of the connectors, controls, and indicators.
SUB 10A in conjunction with passive SAT Series speakers
Connect the passive SAT Series speakers to the speaker outputs (SPEAKER OUT LEFT / RIGHT) of the SUB10A.
Up to four SAT42G2(W) or SAT62G2(W) speakers per speaker output can be operated in parallel. The speaker signal is simply looped through to the
next speaker via the connector panel on the rear of the passive speaker.
Up to two SAT242G2(W) or SAT862G2(W) speakers per speaker output can be operated in parallel. The speaker signal is simply looped through to the
next speaker via the connector panel on the rear of the passive speaker.
We recommend using speaker cable with a conductor cross-section of at least 2 x 1.5 mm².
SUB10A in conjunction with SAT62AG2(W) and SAT82AG2(W) active speakers
Connect the active speakers to the line outputs (LINE DIRECT OUTPUT) of the SUB10A.
Looping Through the signal
With the SAT62AG2(W) and SAT82AG2(W) active speakers, the audio signal can be looped through to additional systems using a three-pole XLR cable.
Accordingly, it is not necessary to connect each device to the audio source individually. Please use high-quality XLR cables for this and ensure that
they are connected carefully.
9
Publicidad
Tabla de contenido
