Ryobi RY28020 Manual Del Operador página 13

TO ATTACH THE STRAIgHT SHAFT gRASS
DEFLECTOR - SS26
See Figure 7.
 Remove the wing screw from the grass deflector.
 Insert the tab on the mounting bracket in the slot on the
grass deflector.
WARNINg:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNINg:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes resulting in possible serious injury.
WARNINg:
Never use blades, flailing devices, wire, or rope on this
product. Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
FUELINg AND REFUELINg THE TRIMMER
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean 1 gallon
container approved for gasoline.
Recommended fuel: This engine is certified to operate on
unleaded gasoline intended for automotive use.
Mix a high quality 2-cycle engine lubricant at 2.6 oz. per
gallon (US).
Do not use automotive lubricant or 2-cycle outboard lubricant.
DO NOT mix quantities larger than usable in a 30 day period.
HIgH qUALITY 2-CYCLE ENgINE LUbRICANT
gASOLINE
1 gallon (US)
1 liter
ASSEMbLY
 Align the screw hole in the mounting bracket with the
 Insert the wing screw through the mounting bracket and
 Tighten the screw securely.
OPERATION
FILLINg TANK
 C l e a n s u r f a c e a ro u n d f u e l c a p t o p re v e n t
 Loosen fuel cap slowly. Rest the cap on a clean
 Carefully pour fuel into the tank. Avoid spillage.
 Prior to replacing the fuel cap, clean and inspect the
 Immediately replace fuel cap and hand tighten. Wipe up
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Move at least
30 ft. from refueling site before starting engine. Do not
smoke! Failure to heed this warning could result in seri-
ous personal injury.
OXYgENATED FUELS
DO NOT USE E85 FUEL. IT WILL VOID YOUR
WARRANTY.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated below are not
covered under warranty.
Ethanol. Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) or 15% ethanol by volume
(commonly referred to as E15) are acceptable. E85 is not.
STARTINg AND STOPPINg
See Figures 8 - 10.
Trimmer should be on a flat, bare surface for starting.
To start a cold engine:
 Slowly press the primer bulb 10 times.
LUbRICANT
2.6 oz.
20 cc (20 ml)
 Set the choke lever to the FULL CHOKE position.
8 — English
screw hole in the grass deflector.
into the grass deflector.
contamination.
surface.
gasket.
any fuel spillage.
WARNINg:
NOTE: After the 7th press, fuel should be visible in the
primer bulb. If it is not, continue to press the primer until
you see fuel in the bulb.