Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Gear speed
Drilling capacities
(Diameter)
No load speed
Overall length (with battery cartridge BL4040)
*With the front handle extended
Rated voltage
Net weight
•
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or
1.
dark areas invite accidents.
2.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while
3.
operating a power tool. Distractions can cause
you to lose control.
Steel
Wood
GAD01
High
Low
Auger bit:
Auger bit:
50 mm (2")
50 mm (2")
Self-feed bit:
Self-feed bit:
65 mm (2-9/16")
118 mm (4-5/8")
Hole saw:
Hole saw:
105 mm (4-1/8")
159 mm (6-1/4")
0 - 1,500 /min
0 - 400 /min
* 614 mm (24-1/4")
D.C. 36 V - 40 V max
5.3 - 5.9 kg (11.7 - 13.0 lbs)
Electrical Safety
1.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
2.
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3.
Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
Do not abuse the cord. Never use the cord for
4.
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
2 ENGLISH
GAD02
High
13 mm (1/2")
Auger bit:
50 mm (2")
Self-feed bit:
65 mm (2-9/16")
118 mm (4-5/8")
Hole saw:
105 mm (4-1/8")
159 mm (6-1/4")
0 - 1,500 /min
545 mm (21-1/2")
4.9 - 5.5 kg (10.8 - 12.1 lbs)
BL4025 / BL4040
DC40RA
Low
Auger bit:
50 mm (2")
Self-feed bit:
Hole saw:
0 - 400 /min
Publicidad
