Black and Decker BEG010-QS Manual De Instrucciones página 5

d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools.
Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may
affect the power tools operation. If damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings Common for
Grinding, Sanding, Wire Brushing or Abrasive
Cutting-Off Operations:
This power tool is intended to function as a grinder,
u
sander, wire brush, polisher or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Operations for which the power tool was not designed
u
may create a hazard and cause personal injury.
Do not use accessories which are not specifically
u
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
The rated speed of the accessory must be at least
u
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
The outside diameter and the thickness of your
u
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
Threaded mounting of accessories must match the
u
grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange.
(Original instructions)
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
Do not use a damaged accessory. Before each use
u
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory and run the
power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during this
test time.
Wear personal protective equipment. Depending on
u
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or
respirator must be capable of filtering particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
Keep bystanders a safe distance away from work
u
area. Anyone entering the work area must wear
personal protective equipment. Fragments of workpiece
or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
Hold power tool by insulated gripping surfaces only,
u
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and shock the
operator.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Position the cord clear of the spinning accessory. If
u
you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
Never lay the power tool down until the accessory
u
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your
u
side. Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
Regularly clean the power tool's air vents. The motor's
u
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
ENGLISH
5