Publicidad
Idiomas disponibles
Idiomas disponibles
Fixed frame screen installation manual
The screen product is manufactured in compliance with the provisions of the following EC directives: 2014-35-CE LDV Low voltage
The screen described in this manual must be used exclusively as a support for video projection. Any other use not covered by this manual, it is not consented.
The screen contains one or more Fabric/sheet of projection. The Fabric of projection is a cadmium-free plastic pvc sheet or Glass wire (continuos filament) plastified PVC impregnated, any fabric can be
classified in category:
-
M1 and M2 fire classification under French standards (LNE Laboratoire national de métrologie et d'essais – French Companies CREPIM – Efectis France);
-
B1 and B2 fire classification under German standards (Exova Warringtonfire Laboratory of Frankfurt am Main);
-
Bs1d0 fire classification under Italian standards (Italian Interior Ministry).
In the absence of a standardisation at a European level of the various national classification norms, it should be noted that the French M1 class corresponds to non flammable material and that M2 class
corresponds to flame retardant material. The screens use projection fabrics/sheets composed mainly of plasticized PVC or fibreglass. As these fabrics are sensitive to temperature and humidity, the
acceptable size tolerance is 1% in each dimension.
There is a tolerance of +/-2 mm on the aluminium profiles used.
The tollerance on the overall size are:
-
+/- 3 mm up to an overall size of 2500 mm;
-
+/- 5 mm up to an overall size of 4000 mm;
-
+/- 10 mm up to an overall size of 8000 mm;
-
+/- 20 mm up to an overall size of 16000 mm;
-
+/- 30 mm up to an overall size of 24000 mm.
Screens and their projection surfaces are delicate and must be cleaned with great care, according to the following instructions:
Never use solvents, chemical or abrasive products, or pointed tools to clean the surface.
Avoid contact with other materials (varnishes, inks etc) as they might be impossible to remove from the canvas.
FABRIC CLEARPIX: Use a soft, clean, dampened cloth, wiping from the center of the projection surface towards the outer edges. A vacuum-cleaner brush may be used, provided its bristles are soft and
perfectly clean.
FABRIC SOLIDPIX, MULTIPIX,: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary.
Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning operations can cause electrostatic
charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being attracted again
FABRIC SILVERPIX is Mandatory to read the instructions accompanying the fabric screen
GENERIC PROFILE: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary
VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft, antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles are soft and perfectly clean.
STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring capacity of its brackets must be checked regularly. In case of canvas deformation or rips, or loosening of structural
components such as brackets or screws, action must be taken immediately to clear the area around the screen and avoid hazard to people and things, replace the defective component and restore the
product's functionality.
Ensure that the screen has suffered no damage during transport. Should any fault be detected, promptly notify your dealer. Verify that all screen accessories have been included
ATTENZIONE do not use cutters or sharp objects to open the wrapping, always use protection gloves when unpacking, handling and installing the product. Depending on the product's weight (reference load:
25 Kg male – 15 Kg female), handling and installing operations should be performed by two, three or people people at least. For heavier loads we recommend the use of specific lifting equipment.
WARNING: When installing the screen use plugs and screws suitable for the screen's weight and for the type of wall or ceiling on which the mount brackets are to be fixed, based on the
following criteria
Screen width view area up to inches
Overall weight
Screen width view area up to inches
Overall weight
See images on the end pages of this manual
Made by Adeo Screen Sp. Z o.o. (Poland) Specifications are subject to change without notice. E&OE
Please verify that you are working with the latest revision of this document before specifying your screen.
Doc: FCIN1 Installation Manual rev3 |07.01.2021
04 GENERAL CHARACTERISTICS OF THE PRODUCT
05 CLEANING AND MAINTENANCE
06 UNPACKING AND HANDING THE SCREEN
07 INSTALLATION INSTRUCTIONS
250"
260"
270"
180 lbs
197 lbs
205 lbs
86 kg
90 kg
93 kg
360"
370"
380"
356 lbs
364 lbs
373 lbs
162 kg
166 kg
170 kg
2014-30-EU EMC Electromagnetic compatibility
2014-53-CE Radio Equipment
2009-125-CE CONSUMPTION Ecodesign
2015-863-EC ROHS Restriction of Hazardous Substances
2012-19-CE RAEE Waste management
2001-95-CE SAFETY Safe Product
280"
290"
300"
213 lbs
296 lbs
304 lbs
97 kg
135 kg
139 kg
390"
400"
500"
382 lbs
391 lbs
571 lbs
174 kg
178 kg
260 kg
310"
320"
330"
313 lbs
322 lbs
330 lbs
142 kg
146 kg
150 kg
600"
700"
800"
716 lbs
830 lbs
993 lbs
325 kg
377 kg
451 kg
Page 6
ENGLISH
340"
350"
338 lbs
347 lbs
154 kg
158 kg
900"
1205lbs
548 kg
Publicidad
