BOMANN DB 765 CB Instrucciones De Servicio/Garantía página 25

4. Sort out the garments according to their ironing temperatures.
Start with the lower temperatures. It is set with the thermostat (1):
Synthetics, silk
Wool
Cotton, linen
MAX
5. Electrical connection
• Make sure that the iron voltage (see name plate) and
the line voltage match.
• Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
6. The control lamp (2) lights up. As soon as it shuts off, the
set temperature is reached. Now you can start to iron.
7. Always pull the plug out of the socket after using the iron.
Steam Ironing ( )
For this a high temperature is needed (cotton, linen).
The quantity of steam can be regulated using the steam quantity
regulator (4). Push it down if necessary in order to turn it.
„O"
„ "
„ "
Extra steam can be added with the steam jet function „ " (3).
Turn the button to the symbol and press it intermittently.
WARNING: The steam is hot. Danger of scalding!
When ironing at low temperatures (minimum temperature level
„• •"), make sure that you reduce the quantity of steam or iron
without steam. If the temperature is too low water may leak from
the soleplate.
Refi lling the water tank
• Always disconnect the mains plug before refi lling water.
• Set the steam control (4) to „O" (no steam). Fill in water
through the fi lling hole (6). Using a fi lling container. Do not
exceed the maximum line as marked on the water reservoir.
Spray Function ( )
In order to moisten a section to be ironed press the spray button
(3). Turn the button to the symbol and press it intermittently.
Vertical Steam
This can be used to produce a jet of steam in a vertical direction.
NOTE:
To avoid excess water leaking from the soleplate do not
operate the steam burst for more than 5 seconds without
interruption.
05-DB 765 CB 25
low temperature
medium temperature
high temperature
maximum temperature
no steam
Small steam volume
Large steam volume
Self-Cleaning ( )
1. Half fi ll the water tank with water.
2. Heat the machine up to its maximum temperature. After the
control lamp goes off remove the machine from the mains
supply.
3. Now hold the iron horizontally over a sink. Turn the steam
quantity control to the „
Now rock the device backwards and forwards until the tank
is empty. Reinsert the control, paying attention to the guide
mechanism. Then return the regulator to the „O" position.
4. Place the machine back on its stand and heat it up again. To
clean the base now iron over a clean cotton cloth.
Cleaning and Storage
• Always remove the mains lead before cleaning!
• Clean the casing with a slightly damp cloth.
• Clean the iron with a slightly humid cloth.
• Always return the steam regulator to the „O" position after
use and empty the water tank in order to prevent any leaks.
• The device must never be immersed in water!
Technical Data
Model:.......................................................................... DB 765 CB
Power supply:............................................................230 V, 50 Hz
Power consumption:..........................................................2000 W
Protection class:........................................................................... Ι
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
Guarantee
The device supplied by our Company is covered by a 24 month
guarantee starting on the date of purchase (receipt).
During the life of the guarantee any fault of the device or its
accessories ascribable to material or manufacturing defects will
be eliminated free of charge by repairing or, at our discretion, by
replacing it. The guarantee services do not entail an extension
of the life of the guarantee nor do they give rise to any right to a
new guarantee!
Proof of the guarantee is provided by the proof of purchase.
Without proof of purchase no free replacement or repair will be
carried out.
If you wish to make a claim under the guarantee please return
the entire machine in the original packaging to your dealer
together with the receipt.
Defects to consumables or parts subject to wearing as well as
cleaning, maintenance or the replacement of said parts are not
covered by the guarantee and hence are to be paid!
The guarantee lapses in case of unauthorized tampering.
" position and pull it out.
25
15.05.2007, 9:44:04 Uhr