Publicidad
Idiomas disponibles
Idiomas disponibles
improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorised service providers.
Riveter Safety Warnings
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
Do not work without a collection container. Mandrels are
ejected to the rear by the riveter and can cause injuries.
Do not point the riveter at persons or yourself during
•
operation and do not work without material to be
riveted. The blind rivet can be ejected from the riveter and
cause injuries.
After the riveting process is completed tilt the unit
•
backwards, so that the residual mandrels fall into the
collection container.
•
Ventilation slots for the engine must not be covered;
do not insert any objects into them. Damage or personal
injury could result.
•
When not in use, place tool on its side on a stable surface
where it will not cause a tripping or falling hazard. Some
tools with large battery packs will stand upright on the battery
pack but may be easily knocked over.
•
Disconnect the power tool from the power supply/
battery if it cannot be switched off. Do not use the power
tool if it cannot be switched on and off with the switch.
Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Chargers
D
WALT chargers require no adjustment and are designed to be
e
as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
i
your charger corresponds to that of your mains.
Your D
WALT charger is double insulated in
e
accordance with EN60335; therefore, no earth wire
is required.
If the supply cord is damaged, it must be replaced only by
D
WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (refer to Technical Data). The
minimum conductor size is 1 mm
When using a cable reel, always unwind the cable completely.
Important Safety Instructions for All
Battery Chargers
saVE ThEsE InsTRUcTIOns: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data). Before using charger, read all
instructions and cautionary markings on charger, battery pack, and
product using battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30 mA or less.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only D
WALT rechargeable batteries. Other types of
e
batteries may burst, causing personal injury and damage.
CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean.
DO NOT attempt to charge the battery pack with any
•
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to work together.
EnGLIsh
; the maximum length is 30 m.
2
27
Publicidad
