Bosch 2800 RE Manual Original página 25

OBJ_BUCH-318-003.book Page 25 Friday, November 19, 2010 4:36 PM
Changing the Tool
The dust protection cap 4 largely prevents the
entry of drilling dust into the tool holder during
operation. When inserting the tool, take care
that the dust protection cap 4 is not damaged.
A damaged dust protection cap should be
changed immediately. We recommend hav-
ing this carried out by an after-sales serv-
ice.
Inserting SDS-plus Drilling Tools
(see figure G)
The SDS-plus drill chuck allows for simple and
convenient changing of drilling tools without the
use of additional tools.
– PBH 3000-2 FRE: Insert the SDS-plus quick
change chuck 2.
– Clean and lightly grease the shank end of the
tool.
– Insert the tool in a twisting manner into the
tool holder until it latches itself.
– Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus
drilling tool can move freely. This causes a cer-
tain radial run-out at no-load, which has no ef-
fect on the accuracy of the drill hole, as the drill
bit centres itself upon drilling.
Removing SDS-plus Drilling Tools
(see figure H)
– Push back the locking sleeve 5 and remove
the tool.
Inserting Drilling Tools without SDS-plus into
the Key Type Drill Chuck (PBH 2800 RE)
Note: Do not use tools without SDS-plus for
hammer drilling or chiselling! Tools without
SDS-plus and their drill chucks are damaged by
hammer drilling or chiselling.
– Insert the key type drill chuck 21.
– Open the key type drill chuck 21 by turning
until the tool can be inserted. Insert the tool.
– Insert the chuck key into the corresponding
holes of the key type drill chuck 21 and clamp
the tool uniformly.
– Turn the mode selector switch 12 to the
"drilling" position.
Bosch Power Tools
Removing Drilling Tools without SDS-plus from
the Key Type Drill Chuck (PBH 2800 RE)
– Turn the sleeve of the key type drill chuck 21
with the drill chuck key in anticlockwise di-
rection until the drilling tool can be removed.
Inserting Drilling Tools without SDS-plus into
the Keyless Chuck
(PBH 2900 FRE/PBH 3000 FRE Set/
PBH 3000-2 FRE) (see figure I)
Note: Do not use tools without SDS-plus for
hammer drilling or chiselling! Tools without
SDS-plus and their drill chucks are damaged by
hammer drilling or chiselling.
– PBH 2900 FRE/PBH 3000 FRE Set: Insert the
keyless chuck 23.
– PBH 3000-2 FRE: Insert the quick change
keyless chuck 1.
– Hold the rear sleeve 26 of the keyless chuck
23 and turn the front sleeve 25 in anticlock-
wise direction until until the tool can be in-
serted. Insert the tool.
– Tightly hold the rear sleeve of the keyless
chuck 23 and firmly turn the front sleeve
clockwise by hand until the locking action is
no longer heard. This automatically locks the
drill chuck.
– Check the tight seating by pulling the tool.
Note: If the tool holder was opened to the stop,
then a latching noise possibly may be heard
while closing the tool holder and the tool holder
will not close.
In this case, turn the front sleeve 25 once in an-
ticlockwise direction. Afterwards, the tool hold-
er can be closed (tightened).
– Turn the mode selector switch 12 to the
"drilling" position.
Removing Drilling Tools without SDS-plus from
the Keyless Chuck
(PBH 2900 FRE/PBH 3000 FRE Set/
PBH 3000-2 FRE) (see figure J)
– Firmly hold the rear sleeve 26 of the keyless
chuck and turn the front sleeve 25 of the key-
less chuck in anticlockwise direction until
the drilling tool can be removed.
1 609 929 T39 | (19.11.10)
English | 25