DeWalt DCD1623 Manual De Instrucciones página 37

If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Refer to the Speed (RPM) and Drill Settings chart
at the back of this section for speed and cutter size
recommendations.
Forward/Reverse Button (Fig. M)
A forward/reverse control button
of bit rotation.
NoTE: The reverse feature of this tool is used for tapping
screw holes. Reverse speed will be 350 rpms in low gear and
680 rpm in high gear regardless of variable speed.
To select forward rotation, release the ON/OFF switch
and switch the forward/reverse control button towards the
forward icon 40 .
To select reverse, switch the forward/reverse control
button towards the reverse icon
Adjusting the Motor Height (Fig. I)
The motor height can be adjusted to accommodate the need
for more or less bit clearance over the workpiece.
1. Loosen the motor slide lever
2. Position the motor to the desired height.
3. Tighten the motor slide lever firmly to secure the motor
in position.
NoTE: There are three set screws
the frame that can be tigthened or loosened to adjust
how easily the motor housing moves with the feed
handle 6 .
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Carry handle (Fig. J)
This carry handle has two functions:
• Carry the tool when it is in vertical position.
• Protect the battery from dropping off in its folded
position for tool's upside down application.
Installing and Removing the Battery Pack
(Fig. J, K)

WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.

WARNING: Keep cutting fluid away from the battery
pack. Contact with cutting fluid may cause the battery
housing to crack. If battery comes in contact with
cutting fluid, clean the battery immediately.
NoTE: It is highly recommended that battery packs with oil
resistant housings (glass filled nylon, designated by a G suffix
in the model number) be used. For best results, make sure
your battery pack is fully charged.
To install the battery pack
and hold the carry handle release button
determines the direction
3
.
41
12 .
38 along the side of
into the battery port
29
and move the
8
carry handle
pack with the rails inside the battery port and slide it in until
the battery pack is firmly seated in the tool and ensure that it
does not disengage.
To remove the battery pack from the tool, press and hold
the carry handle release button
handle
22
button
30
port. Insert it into the charger as described in the charger
section of this manual.
NoTE: If the battery is still difficult to remove with the carry
handle in the vertical position, press and hold the carry
handle release button and push the carry handle a little
1
further towards the front of the tool to create more space for
the battery to be removed.
Prior to operation

WARNING: Inspect the chain before each use, for wear
or damage. Replace if necessary.
Try a few simple projects using scrap material until you
develop a "feel" for the machine.
Switching On and Off (Fig. A)
In order to operate properly, the machine has to be switched
following the procedure as described below.
Switching the power on and off

WARNING: In a vertical or upside down application,
the tool will drop off from the workpiece if the magnet
engagement lever is NOT at the 100% position.
Push the power switch
NoTE: The tool will not run unless magnet is at 100%
engagement. An orange light will illuminate indicating the
magnet is not fully engaged.
Press the switch down (0) to shut down the tool.
E‑Clutch
Indicator LED (Fig. A)
The DCD1623 is equipped with the D
system. This feature senses the motion of the tool and shuts
the tool down if necessary. The E‑Clutch® indicator
illuminate red to indicate status.
The working LED on the front of the magnetic base
flash to alert the user of low voltage conditions.
INDICaToR DIaGNosIs
OFF
RED
SOLID
ORANGE
SOLID
press
31
22 into the vertical position. Align the battery
and move the carry
8
into the vertical position. Press the release
and firmly pull the battery pack out of the battery
1 up (I) to run the tool.
System and Low Voltage
®
Tool is functioning Follow all warnings and instructions
normally when operating the tool.
E‑Clutch ® System With the tool properly supported,
has been activated release trigger. The tool will
(ENGAGED) function normally when the trigger
is depressed again and the indicator
light will go out.
The magnet Move the magnet engagement
engagement lever lever to the 100% position.
is not in the 100%
position with the
power switch on.
ENGlIsh
WALT E‑Clutch®
e
24 will
will
20
solUTIoN
35