Makita ELM4612 Manual De Instrucciones Original página 10

6) Thoroughly inspect the area where the equipment is to
be used and remove all objects which can be thrown
by the machine.
7) Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn
or damaged. Replace worn or damaged blades and
bolts in sets to preserve balance.
8) Mow only in daylight or in good artificial light.
9) Avoid operating the equipment in wet grass, where
feasible.
10) Always be sure of your footing on slopes.
11) Walk, never run.
12) For wheeled rotary machines; mow across the face of
slopes, never up and down.
13) Exercise extreme caution when changing direction on
slopes.
14) Do not mow excessively on steep slopes.
15) Use extreme caution when reversing or pulling the
lawn mower towards you.
16) Stop the blade if the lawn mower has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the lawn mower to and
from the area to be mowed.
17) Never operate the lawn mower with defective guards,
or without safety devices, for example deflectors and/
or grass catchers, in place.
18) Start or switch on the motor carefully according to
instructions and with feet well away from the blades.
19) Do not tilt the lawn mower when starting switching on
the motor, except if the lawn mower has to be tilted for
starting. In this case, do not tilt it more than absolutely
necessary and lift only the part which is away from the
operator.
20) Do not start the motor when standing in front of the
discharge chute.
21) Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
22) Never pick up or carry a lawn mower while the motor
is running.
23) Stop the motor and disconnect the plug:
- before clearing blockages or unclogging chute;
- before checking, cleaning or working on the lawn
mower;
- after striking a foreign object. Inspect the lawn
mower for damage and make repairs before
restarting and operating the lawn mower;
- if lawn mower starts to vibrate abnormally (check
immediately).
24) Stop the mower:
- whenever you leave the lawn mower.
25) Keep all nuts, blots and screws tight to be sure the
equipment is in safe working condition.
26) Check the grass catcher frequently for wear or
deterioration.
27) Replace worn or damaged parts for safety.
28) Do not use the lawn mower if the cords are damaged
or worn.
29) Do not connect a damaged cord to the supply or touch
a damaged cord before it is disconnected from the
supply. A damaged cord can lead to contact with live
parts.
30) Do not touch the blade before the machine is
disconnected from the supply and the blade have
come to a complete stop.
10
All manuals and user guides at all-guides.com
31) To keep extension cords away from the blade. The
32) To disconnect the supply (i.e. pulling the plug from the
33) Children should be supervised to ensure that they do
34) This appliance is not intended for use by persons
35) If the supply cord is damaged, it must be replaced by a
36) Instructions for the safe operation of the appliance,
37) Be careful during adjustment of the machine to
38) Always allow the machine to cool before storing.
39) When servicing the blades be aware that, even though
40) Replace worn or damaged parts for safety; Use only
41) Be careful during adjustment of the appliance to
42) Before use check the supply and extension cord for
43) If the supply cord is damaged, it must be replaced by
3. PARTS DESCRIPTION (Fig. 1,
blade can cause damage to the cords and lead to
contact with live parts.
socket):
- whenever leaving the machine unattended;
- before clearing a blockage;
- before checking, cleaning or working on the
machine;
- after striking a foreign object;
- whenever the machine starts vibrating abnormally.
not play with the appliance.
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
special cord or assembly available from the
manufacturer or its service agent.
including a recommendation that the appliance should
be supplied via a Residual Current Device (RCD) with
a tripping current of not more than 30 mA.
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
the power source is switched off, the blades can still
be moved.
genuine replacement parts and accessories.
prevent entrapment of the fingers between moving
blades and fixed parts of appliance.
signs of damage or worn. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD
BEFORE DISCONNECTING THE SUPPLY. Do not
use the appliance if the cord is damaged or worn.
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Fig. 2)