JB Systems Light LED Jive Manual De Instrucciones página 4

ENGLISH
DESCRIPTION:
1. Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
2. Rotating optical barrel, don't touch while in use.
3. DISPLAY: shows the various menus and the selected functions.
4. Button:
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
5. LED:
On
MENU DMX input present
DOWN On Master Mode
UP On Slave Mode
ENTER Flashing Sound activation
6. WIRED REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is
used in standalone or master/slave mode.
7. WIRELESS REMOTE CONTROL INPUT: Used to connect RF-8 wireless controller while the unit is
used in standalone or master/slave mode.
8. Internal microphone: Receives the sound to control the unit
9. SAFETY EYEBOLT: used to attach a safety cable when the unit is rigged (see paragraph "overhead
rigging.
10. DMX input: For DMX512 link, use a 3/5-pin XLR plug cable to input DMX signal
11. DMX output: For DMX512 link, use a 3-pin XLR plug cable to link the next unit.
12. Mains output: Here you can connect a special male/female IEC cable to supply power for the next
unit.
13. Mains input with IEC socket and integrated fuse holder. Connect the supplied mains cable here.
MAIN MENU:
 To select any of the functions, press the MENU button up to when the required one is shown on the
display or use the DOWN and UP buttons to browse the menu.
 Select the function with the ENTER button (the display blinks).
 Use DOWN and UP buttons to change the mode.
 Once the required mode is selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button shortly. The main menu is shown
in the chart.
JB SYSTEMS 3/53
®
OPERATION MANUAL
LED JIVE
ENGLISH
DMX Address
Used to set the starting address in a
DMX setup.
 Press the MENU button until "Addr" is
shown on the display.
 Press the ENTER button, the display
starts blinking.
 Use DOWN and UP buttons to change
the DMX address.
 Once the correct address shows on
the display, press the ENTER button
to save it.
To go back to the main menu without
any change press the MENU button
shortly.
If you want to go back to normal running
mode: press the MENU button for about
2 seconds.
Channel mode
Used to set the desired channel setup
mode.
 Press the MENU button until "ChMd"
is shown on the display.
 Press the ENTER button, the display
starts blinking.
 Use DOWN and UP buttons to choose
1MSL, 1ch or 5Ch.
 Once the desired channel setup mode
shows on the display, press the
ENTER button to save it.
To go back to the main menu without
any change press the MENU button
shortly.
If you want to go back to normal running
mode: press the MENU button for about
2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the MENU button until "SLMd" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "SL 1" (normal) or "SL 2" (2 light show) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Show Mode
Used to choose the Show mode when used in standalone or master/slave mode.
 Press the MENU button until "ShMd" is showing on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select one of the available shows:
 LED JIVE: has 8 shows show1 (Sh 1) to show8 (Sh 8)
 Once the right mode shows on the display, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
JB SYSTEMS 4/53
®
OPERATION MANUAL
LED JIVE