Publicidad
Idiomas disponibles
Idiomas disponibles
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
The RBRC® Seal
The RBRC® (Rechargeable Battery Recycling
Corporation) Seal on the nickel cadmium,
nickel metal hydride or lithium-ion batteries
(or battery packs) indicates that the costs
to recycle these batteries (or battery packs)
at the end of their useful life have already been paid by
BLACK+DECKER. In some areas, it is illegal to place spent
nickel cadmium, nickel metal hydride or lithium-ion
batteries in the trash or municipal solid waste stream and
the Call 2 Recycle® program provides an environmentally
conscious alternative.
Call 2 Recycle, Inc., in cooperation with BLACK+DECKER
and other battery users, has established the program in
the United States and Canada to facilitate the collection
of spent nickel cadmium, nickel metal hydride or
lithium-ion batteries. Help protect our environment and
conserve natural resources by returning the spent nickel
cadmium, nickel metal hydride or lithium-ion batteries
to an authorized BLACK+DECKER service center or to
your local retailer for recycling. You may also contact your
local recycling center for information on where to drop
off the spent battery. RBRC® is a registered trademark of
Call 2 Recycle, Inc.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F – 75 °F (18 ° – 24 °C). DO NOT charge the
battery pack in an air temperature below 40 °F (4.5 °C),
or above 104 °F (40 °C). This is important and will
prevent serious damage to the battery pack.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the power adapter and battery pack to a
location where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and USB cable to your local service center.
3. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
Transportation
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do
not place the battery pack in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and
the like. The US Department of Transportation
Hazardous Material Regulations (HMR) actually
prohibit transporting batteries in commerce or on
airplanes in carry-on baggage UNLESS they are
properly protected from short circuits. So when
transporting individual battery packs, make sure that
the battery terminals are protected and well insulated
from materials that could contact them and cause a
short circuit.
CAUTION: GoPak battery terminal cap should be
used when battery is not connected to a power tool.
Terminal cap is provided for use whenever the battery
is out of the tool. Remove cap before placing battery
into tool.
FCC requirements for all digital devices
This device complies with Part 15 of the FCC Rules and Industry
Canada License-exempt RSS standard(s). Operation is subject to the
following two conditions:
1 . This device may not cause harmful interference, and
2 . This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following meaures:
ʵ
Reorient or relocate the receiving antenna.
ʵ
Increase the separation between the equipment
and receiver.
ʵ
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
ʵ
Consult the dealer or an experienced radio/TV
technician for help.
CAN ICES-3(B)/NMB-3(B)
Getting Started
•
The Micro USB port
in 1 battery is only to be used for charging the GoPak.
•
The USB A port
on the BLACK+DECKER GoPak 2 in 1
10
battery is only to be used for powering USB devices
(Phone/Tablet/MP3/Wearable/Game Controller/etc.).
6
on the BLACK+DECKER GoPak 2
English
5
Publicidad
