Publicidad
Idiomas disponibles
Idiomas disponibles
5. Glue, assemble and clamp the joint.
6. For joints other than 90 ° see outside registration column
Figure CC for proper fence angle setting.
The above method will produce a joint where the outside
surfaces of the joint are aligned. If you wish to produce a
joint where the inside surfaces are aligned, use the following
procedures for a 90 ° joint.
7. Position workpieces as they are to be assembled.
8. Layout biscuit locations on the inside of the angle.
9. Set up tool by setting fence angle to 45 °. Set vertical
fence adjustment so that the biscuit is located toward
the inside of the joint where material is thicker. Select
biscuit size so that the blade does not protrude through
the outside face of the material.
10. Clamp the workpiece and align the tool as shown in
Figure DD.
11. Make the plunge cut and repeat for all biscuit locations.
12. Glue, assemble and clamp the joint.
13. For joints other than 90 ° see inside registration column
in Figure CC for proper fence angle setting.
T‑Joints (Fig. EE–HH)
Biscuit joining is a viable alternative to dadoing when making
a T‑joint. T‑joints are most commonly used when attaching
shelves to the sides of a case. The method described below
will work if your shelf material is at least 5/8" thick.
1. Place the workpieces on a work surface exactly as you
will be assembling them in the form of an upside down
"T." Mark lightly along the joint where the top of the shelf
is to end up (see Figure FF). Mark biscuit locations at the
joint interface on the shelf piece only.
2. Lay the shelf down on the mating workpiece. Clamp the
two workpieces together and to the work surface in this
position (see Figure GG).
3. Set up the tool by selecting the proper biscuit size and
setting the adjustable fence angle at 0 °.
4. Using the bottom registration surface, align the tool
with the biscuit location marks and make a vertical and a
horizontal plunge cut for each biscuit location as shown
in Figure HH.
5. Glue, assemble and clamp the joint.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
www.dewalt.com.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/Legal/
Warranty/3‑Year‑Limited‑Warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
English
e
WALT call or visit our website:
e
WALT factory service center or a
e
WALT
e
WALT
WALT
e
19
Publicidad
