Publicidad
Idiomas disponibles
Idiomas disponibles
Cutting Tool Safety
WARNING: Before connecting a tool to a power source (mains
switch power point receptacle, outlet, etc.) be sure that the voltage
supply is the same as that specified on the nameplate of the tool. A
power source with a voltage greater than that specified for the tool
can result in serious injury to the user, and damage to the tool. If in
doubt, do not plug in the tool. Using a power source with a voltage
less than the nameplate rating is harmful to the motor.
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a
tool is suitable without checking the product literature before
use
Protect your eyes
• Always wear appropriate eye protection when using cutting
tools
• Spectacles are not designed to offer any protection when using
this product; normal lenses are not impact resistant and could
shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise
exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust
masks
Protect your hands
• Do not allow hands to get close to the cutting wheel or
blades. Use a suitable push stick for shorter workpieces with
appropriate power tools
Be aware of others around you
• It is the responsibility of the user to ensure that other people
in the vicinity of the work area are not exposed to dangerous
noise or dust and are also provided with suitable protective
equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded
objects before cutting
• Do not attempt to cut material that contains embedded objects
unless you know that the cutting tool fitted to your machine is
suitable for the job
• Walls may conceal wiring and piping, car body panels may
conceal fuel lines, and long grass may conceal stones and glass.
Always check the work area thoroughly before proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed
from the cutting tool. It is the user's responsibility to ensure that
other people in the work area are protected from the possibility
of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check
that wrenches / adjusters are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
• Ensure blades are sharp, in good condition and correctly fitted
982168_OwnerManual.indd 7
982168_OwnerManual.indd 7
• Do not attempt to resharpen blades that are not suitable for
resharpening, these may include specially hardened blades
or blades made from hardened alloys typically containing
tungsten
• Blades that can be resharpened should be resharpened
only according the blade manufacturer's instructions. These
may include a limited number of times the blade can be
resharpened
• Sharpened blades should be more thoroughly inspected before
use and replaced immediately if there is any doubt about their
condition and suitability for use
• In the event blades encounter an embedded object in use
that the blades are not suitable for, blades should be replaced
immediately
Direction of feed
• Always feed work into the blade or cutter against the direction of
movement of the blade or cutter
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not
attempt to change tools until they have been allowed to cool
completely
Control dust / swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard,
and some metal swarf is explosive
• Be especially careful when cutting wood and metal. Sparks from
metal cutting are a common cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer
working environment
Product Familiarisation
1. Front Handle
2. PCB Air Vents
3. ON/OFF Trigger Switch
4. Trigger Safety Lock
5. Main Handle
6. Fixed Rear Base
7. Fence Attachment Point (x 4)
8. Drive Belt Cover
9. Front Handle Lock Lever
10. Fence Attachment Point (x 4)
11. Movable Front Base
12. Depth Adjustment Knob
13. Front Handle Set Screw
14. Blade Barrel
15. Reversible Blades
16. Clamping Screw (x 5)
17. Blade Spanner
18. Dust/Chip Extraction Port
19. Dust Extraction Adaptor
20. Combined Parallel and Bevel Fence Guide
21. Fence Attachment Knob (x 2)
EN
7
21/11/2022 08:12
21/11/2022 08:12
Publicidad
