DeWalt DCP580 Manual De Instrucciones página 14

ENGLISH
Sharpening High‑Speed Steel Blades
(Fig. L)

CAUTION: Planer blades are extremely sharp. Handle
with great care.
NOTE: Carbide blades cannot be sharpened.
1. Fasten the blades to the sharpening holder
sure both blade edges
2. Place the blade edges so they rest flat on the grinding
stone (not included).
3. Firmly grip the sharpening holder and move it back and
forward to sharpen the blade edges
Kickstand (Fig. M)
Your planer is equipped with a kickstand
the rear shoe that automatically lowers when the tool is
4
lifted from the work surface allowing the planer to set on the
work surface without the blade touching it. When planing,
the kickstand raises as the tool is pushed forward through
the material. If the kickstand obstructs special planing work,
it can be stored and locked out of the way.

CAUTION: Be sure that the kickstand is correctly
extended when setting the planer on a work surface.
Edge Chamfering (Fig. N)
Your planer has a precision machined chamfering groove
in the front shoe for planing along a corner of the wood. The
width of the groove is 4.5 to 8 mm. It's a good idea to try a
piece of scrap wood before doing finish work.
Dust Extraction (Fig. A, O)
Your planer has a built-in dust extraction port
allows either a dust bag or a shop vacuum to be connected.
The built-in outlet utilizes the D
system making it compatible with the D
To Attach the Dust Bag
While holding the planer, slide the dust bag collar onto the
dust extraction port 12
To Empty The Dust Bag
1. While holding the planer, remove the dust bag by sliding
it off the dust extraction port
2. Gently shake or tap the dust bag to empty.
3. Reattach the dust bag back onto the outlet.
You may notice that all the dust will not come free from
the bag. This will not affect planing performance but will
reduce the planer's dust collection efficiency. To restore your
planer's dust collection efficiency, depress the spring inside
the dust bag when you are emptying it and tap it on the side
of the trash can or dust receptacle.
NOTE: A D WALT AirLock Adapter (DWV9000) can be
e
purchased separately to connect a shop vacuum or D
dust extractor to your planer.

CAUTION: Never operate these tools unless the
dust collector is in place. Planing dust exhaust may
create a breathing hazard.
12
28
21 are facing the same direction.
21 .
located behind
29
12
WALT AirLock connection
e
WALT dust extractor.
e
as shown in Figure O.
.
12
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
. Make
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Chip Discharge Chute
Cleaning Instructions (Fig. A)
If the unit is clogged with dust or chips, use a non-metallic
stick to push the obstruction out of the chip discharge
chute 11
Accessories

30
WARNING: Since accessories, other than those offered
by D
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your tool are available
which
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact D
or visit our website: www.dewalt.com.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of
WALT
e
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
. Never stick your finger into the chute.
WALT, have not been tested with this product, use
e
WALT. Call 1-800-4-D WALT (1-800-433-9258)
e
e
WALT factory service center or a
e
WALT authorized service center. Always use identical
WALT recommended
e