Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
*P517-381*
P517-381
Adjustment
Installation Preparation
Door preparation:
For door preparation use the template included in the package with the
lock. For additional information, visit the website www.allegion.com/us.
IMPORTANT – LOCK TIMING
LOCK TIMING is the positioning and adjustment of internal lock
L
components.
Functions not listed below do not require timing.
L
THE FOLLOWING LOCKING FUNCTIONS MUST BE TIMED:
ND60 (including XN12-001)
ND72 (including XN12-002 and XN12-003)
ND70
ND73
ND93
ND94
ND25x70
ND70x80
See ND-Series Timing Guide (P517-432) in package.
For additional assistance, contact Product Support at
Outside
Lever
Chassis
Plate
Latch
Strike
ND75
ND78
ND95
ND97
1-877-671-7011.
ND-Series
Anti-Rotation
Plate
Optional Spacer
for 1⅜" Door (2)
1
Install latch
The bevel must face toward the door stop.
ND81
ND98
Pin wrench
Mounting
Screws (2)
Inside Spring
Cage
Actual Size
Installation Instructions
Cylinder Options
Full Size IC (FSIC)
Small Format (SFIC)
Standard Cylinder
Inside Lever
Rose
ND53 Function shown
Publicidad
Manuales relacionados para Schlage ND78
Resumen de contenidos para Schlage ND78
- Página 1 LOCK TIMING is the positioning and adjustment of internal lock components. Functions not listed below do not require timing. THE FOLLOWING LOCKING FUNCTIONS MUST BE TIMED: ND60 (including XN12-001) ND72 (including XN12-002 and XN12-003) ND70 ND73 ND75 ND78 ND81 Actual Size ND93 ND94 ND95 ND97 ND98 ND25x70 ND70x80 See ND-Series Timing Guide (P517-432) in package.
- Página 2 Door Thickness Adjustment NOTE: If door thickness insert is missing, align the adjustment plate to marks on chassis: • For 13⁄4” thick doors, NO ADJUSTMENT IS REQUIRED. Continue to step 2. • For 1³⁄8” thick doors, install the optional spacers (see steps 2 and 4). Door No further adjustment is required.
- Página 3 Install chassis/outside lever assembly Install anti-rotation plate Latch prongs fit between slide and slide clip. Align the tab with the indent on the hub. Indent Optional spacer 1⅜” (35 mm) thick door ONLY Indent Anti-rotation Slide clip plate Latch prongs Optional spacer ”...
- Página 4 Install inside lever Check lock function Firmly push on until lever catch engages. If a keyed function does not work properly, refer to the ND-Series Timing Guide (P517-432) in this package to determine proper adjustment of locks that require timing. Lock functions that require timing are listed on page 1.
- Página 5 Las siguientes funciones de bloqueo deben sincronizarse: Tamaño real Les fonctions de verrouillage suivantes doivent être synchronisées : Taille réelle ND60 (incluso/y compris XN12-001) ND72 (incluso/y compris XN12-002, XN12-003) ND70 ND73 ND75 ND78 ND81 ND93 ND94 ND95 ND97 ND98 ND25x70 ND70x80...
- Página 6 Ajuste del gorosor de la puerta Vuelva a orientar y colocar el inserto de espesor de la puerta. Réglage de l’épaisseur de la porte Réorientez l’écrou rapporté de l’épaisseur de la porte et replacez-le. • Para puertas de 44 mm de espesor, no se requiere NINGÚN AJUSTE. Continuar al paso 2.
- Página 7 Vuelva a instalar la placa de ajuste. Instale el chasis/manija exterior Remettre la plaque de réglage. Installer le châssis/levier extérieur Ajuste hasta que el inserto de espesor de la puerta ingrese en la Los dientes del pestillo ajustan entre el deslizador y el gancho lateral. muesca en la placa de ajuste (o alinee como se describe anteriormente).
- Página 8 Instale la placa antirrotación Instale la manija interior Installer la plaque anti-rotation Installer le levier intérieur Alinee el diente con la muesca en el núcleo. Presione firmemente hasta que entre la traba de la manija. Aligner la languette avec la fente sur le collet. Poussez fermement jusqu’à...
- Página 9 PAGE 8 PAGE 3 PAGE 7 BEGINNING SHEET Additional Notes: Revision History Revision Description: E > Artwork revision. Add text on page 1 and page 5 to include new functions ND78, ND81, ND98. 066546 069086 074595 075459 089268 Material Edited By...