Publicidad
Idiomas disponibles
Idiomas disponibles
9. Care & Maintenance
EN
Inflate the Tire
Check the tire pressure every month, and inflate the tires
if the pressure is too low. The recommended tire pressure
is 45 psi.
If there is a lack of air in the front and rear tires, you
may use the extended nozzle supplied with the scooter
to inflate tires. First connect the extension nozzle with
air pump, then unscrew the front (rear) tire valve cap,
and connect the extension nozzle and the valve securely
together, then Inflate the tire.
WARNING! Tire removal is very complicated. Please do
not remove the tire by yourself. Improper operation
may affect the operation of the scooter. Please contact
professional support.
Adjust the Disc Brake
Tool: 4 mm hex key (the tool needs to be prepared
by the user).
Before adjusting, make sure the scooter is turned off
and not being charged. During adjusting, pull the
end of the brake cable to make the cable tight.
If the brake is too tight, use the tool to loosen the
screw by turning it counterclockwise, pull the disc
brake rocker arm outwards, and then tighten the
screw. If the brake is too loose, use the tool to loosen
the screw by turning it counterclockwise, push the
disc brake rocker arm forwards, and then tighten the
screw.
WARNING !
As with any mechanical component, a vehicle is subject to high stresses and wear. The various materials
and components may react differently to wear or fatigue. If the expected service life for a component has been
exceeded, it may break suddenly, therefore risking causing injuries to the user. Cracks, scratches and discoloration
in the areas subject to high stresses indicate that the component has exceeded its service life and please contact an
authorized or a specialized repairer.
016
Valve Cap
Disc Brake
Rocker Arm
Adjusting
Screw
10. Specifications
Name
Product
Model
Vehicle: L × W × H (mm)
[1]
Dimensions
After Folding: L × W × H (mm)
Net Weight
Vehicle Net Weight (kg)
Load Range (kg)
Rider
Age (years)
Body Length (cm)
Max. Speed (km/h)
General Range (km)
[2]
Max. Climbing Angle (%)
Suitable Surfaces
Assembled Electric
Scooter
Operating Temperature (° C)
Storage Temperature (° C)
IP Rating
Charging Time (h)
Model
Nominal Voltage (VDC)
Max. Charge Voltage (VDC)
Rated Energy (Wh)
Battery Pack
Intelligent Battery
Management System
Normal Charging
Temperature Range (° C)
Rated Capacity (Ah)
Wheel Motor
Rated Power (kW; W)
Output Power (kW; W)
Input Voltage (VAC)
Battery Charger
Max. Output Voltage (VDC)
Rated Output (VDC; A)
[3]
Model
Tire
Front & Back Tires
Frequency Band (s)
Bluetooth
Max. RF Power (dBm)
[1] Vehicle height: From the ground to the top of the scooter
[2] General range: Measured when there is no wind and at 25° C, the scooter is fully charged to ride at a constant speed of 15 km/h on a flat
surface with a load of 75 kg.
[3] To recharge the battery, only use the battery charger provided in the package. Please see battery charger parameters in Specifications.
NAVEE Electric Scooter S65
NKP2223-A25
1222 × 551 × 1266
1222 × 549 × 539
24.3
25–120
16–50
120–200
25
Approx. 65
Approx. 25
Cement or asphalt road, with benches of less than 1 cm or crevices
narrower than 3 cm
-10 to 40
-20 to 45
IPX5
Approx. 6.5
P2301-BD5A
46.8
54.6
596.7
Over-heating, short circuit, over-current, over-discharge, and over-
charge protection
0 to 40
12.75
0.5; 500
0.1219; 121.9
220–240
54.6
53.0; 2.3
S126BP5300230
Tubeless self-sealing tires, φ250 × 64 straight valve, with the materials of
natural carbon black and synthetic rubber
2.4000–2.4835 GHz
8
EN
017
Publicidad
