Asist AE6CS25 Manual Del Usuario página 35

ADDITIONAL SAFETY INSTRUCTIONS
The chain sharpener is designed for sharpening
saw chains.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The machine must only be used for its intended
purpose! Even when the equipment is used as
prescribed it is still impossible to eliminate certain
residual risk factors. The following hazards may
arise in connection with the machine's construction
and layout:
• Contact with the grinding wheel where it is not
covered.
• Catapulting of parts from damaged grinding
wheels.
• Catapulting of workpieces and parts of workpieces
from the machine. • Damage to hearing if ear-muffs
are not used
as necessary.
Only connect the device to a socket with a residual
current circuit breaker (FI switch) rated for a maximum
residual current of 30 mA.
• Protect the power and extension cables from the grin-
ding wheel and chain saw. In the event of damage or
cuts, disconnect the plug from immediately plugs.
Do not touch the cable until it is disconnected from the
mains. Danger of electric shock.
• Visually inspect the grinding wheel before use. Do
not use cracked grinding wheels, cracked wheels or
other damage. Worn out replace the grinding wheel.
• Never use the device without a face shield.
• Do not operate the appliance if you are tired or after
consuming alcohol or medication. Remember enough
breaks at work in time.
• Do not use the device in an explosive atmosphere or
in places where flying sparks could cause a fire, ex-
plosion, etc. There is a risk of fire or explosion if not
observed.
• Protect your hands from the grinding wheel when
operating the machine and a chainsaw.
Do not move the chain by hand. There is a risk of in-
jury.
• Never put your fingers between the grinding wheel
and the disc or between the grinding wheel and the
protective cover. There is a risk of pinching.
• The chain heats up to a high temperature during
grinding. Do not touch the workpiece, there is a risk
of burns.
• Use only grinding wheels recommended by the ma-
nufacturer. Do not use saw blades.
• Switch off the appliance and disconnect the mains
plug in the following cases:
- When releasing a blocked tool,
- If the power cord is damaged or jammed,
- In case of unusual sounds.
- Use protective equipment against noise,
dust and vibrations !!!
KEEP THESE SAFETY INSTRUCTIONS FOR
FUTURE REFERENCE !!!
DESCRIPTION (A)
1. Turntable
2. Support table
3a / 3b. Mounting screw
4. Chain stopper
5. Guide plate
6. Guide bar
7. Mounting nut
8. Set screw (for grinding depth)
9. Grinding disc
10. Protective cover
11. Handle
12. ON/OFF switch
13. Grinding head
14. Tail of transparent cover
15. Hexagon nut
16. Flange
17. Warning label
18. Blocking rod
19. Scale for setting the grinding angle (+35° to -35°)
Pictograms
Pictograms and values listed on the product pac-
kaging:
a) Power values
b) Power input
c) Idle speed
a
ASIST tools are intended for home or hobby use only.
The manufacturer and importer do not recommend
using this tool in extreme conditions and under heavy
loads.
Any other additional requirements must be subject
to agreement between the manufacturer and the
customer.
The chain sharpener is intended for sharpening saw
chains.
The machine may only be used for the prescribed
purpose. Any other use is considered abuse. The
machine may only be used for its intended purpose!
Even if the device is used according to the prescrip-
tion, it is still not possible to eliminate certain risk
factors.
Danger:
35
b c d