Publicidad
Idiomas disponibles
Idiomas disponibles
used to deactivate the Child Lock will blink 3 times.
To deactivate the Child Lock:
Press and hold 1
and 2
st
nd
seconds while any programme is running. The lights on the
1
and 2
Auxiliary Function buttons will flash, and "C03",
st
nd
"C02", "C01" will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then, "COFF"
will appear on the display indicating that the Child Lock is
deactivated.
C
In addition to the method above, to deactivate the Child
Lock, switch the Programme Selection knob to On /
Off position when no programme is running, and select
another programme.
Child Lock is not deactivated after power failures or
when the machine is unplugged.
4.13 Progress of programme
Progress of a running programme can be followed from the
Programme Follow-up indicator. At the beginning of every
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
C
If the machine does not pass to the spinning step, Rinse
Hold function might be active or the automatic unbalanced
load detection system might be activated due to the
unbalanced distribution of the laundry in the machine.
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases when
the water level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
illuminates steadily within 1-2 minutes and the loading door
can be opened.
If the level is unsuitable, Loading Door light turns off and the
loading door cannot be opened. If you are obliged to open
the Loading Door while the Loading Door light is off, you
have to cancel the current programme; see "Canceling the
programme".
4.15 Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to
pause mode while a programme is running. The light of
the step which the machine is in starts flashing in the
Programme Follow-up indicator to show that the machine
has been switched to the pause mode.
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
16 / EN
auxiliary function buttons for 3
Changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached, you
may cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C
If no change is allowed, the relevant light will flash for
3 times.
Adding or taking out laundry
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the pause
mode will flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
4.16 Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be canceled. End / Cancel light will flash continuously to
notify that the programme has been canceled.
Pump function is activated for 1-2 minutes regardless of the
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
C
Depending on the step where the programme was
canceled in, you may have to put detergent and
softener again for the programme you have selected
anew.
4.17 End of programme
"End" appears on the display at the end of the programme.
Wait until the loading door light illuminates steadily. Press On
/ Off button to switch off the machine. Take out your laundry
and close the loading door. Your machine is ready for the
next washing cycle.
4.18 Your machine is equipped
with a "Standby Mode"
In case of not starting any programme or waiting without
making any other operation when the machine is turned
on by On/Off button and while it is in selection step or if
no other operation is performed approximately 2 minutes
after the programme you selected has come to an end,
your machine will automatically switch to energy saving
mode. Brightness of indicator lights will decrease. Also,
if your product is equipped with a display showing the
programme duration, this display will completely turn off. In
case of rotating the Programme Selection knob or pressing
any button, lights and display will restore to their previous
condition. Your selections made while exiting the energy
saving mode may change. Check the appropriateness of
your selections before starting the programme. Readjust if
necessary. This is not a fault.
Washing Machine / User's Manual
Publicidad
