Publicidad
Idiomas disponibles
Idiomas disponibles
Bring up the lower thread
When inserting or removing the lower bobbin, the needle must be fully raised.
Turn the handwheel (no.3). Open the hook cover and pull out the plastic window.
Insert the bobbin in the bobbin case, so that the thread rund in a clockwise direction.
Replace the plastic window and the hook cover.
Raise the presser foot, hold the upper thread with the left hand, right hand turn the handwheel
anticlockwise until the needle is raised. When the needle reach the bottom, the hook tray will
hook the upper thread, rotate the hook tray to pull the lower thread out. Pull the lower and
upper thread under presser foot(no.14), pull out 10 cm to the back.
No.14
Winding of the bobine.
Figure 1. Place a yarn pirn on the bobine pin (no.6).
Figure 2. Guide the thread through the winding thread guide (no.7) to the empty bobine.
Figure 3. Wind the thread several times clockwise to the empty bobine and place it on the
bobine winder(no. 5 in figure 1).
Figure 4. Press the bobbin against the bobinestopper.
Start electric winding by pressing the foot control.
When the bobbin is full, release the foot pedal, cut the thread, then remove bobbin
No.6
No.5
No.3
No.7
23
Reverse sewing.
At the end of seam, press down reverse sewing lever, sew a few reverse stitches, fix the trace
to avoid loosing. The reverse trace shouldn't beyound 5 cm. Release the lever and the
machine will sew forward again.
Straight and other stitching
Make sure the bobbin winder (no.5) is selected on "seewing".
There are two kinds of straight stitch for your choise. Turn the pattern seklector dial to the one
you need.wenst. Set the needle at the highest position by turning hand wheel anticlockwise.
Gently pull both threads (about 10 cm) towards rear, raise the presser foot, place the fabric
under the presser foot.
Gently press down the foot control to start sewing. Guide fabriv gently by hand.
Stop the needle in its top position, and thread can be pulled out easily.
Raise the presser foot and remove the fabric.
This for aal the patterns of your choise.
Pattern selector
Buttonholes
Preparation
1.
Raise the presser foot lever, remove the metallic presser foot and replace a
buttonhole foot. (note: before setting buttonhole foot, turn the hand wheel and make
sure that the feed dogs is below the needle plate and the needle have to be about 5
mm above the needle plate.)
2.
Make sure the diameter of the button and add 3 mm (1/8") for the bartacks.
3.
If you have a very thick button, add more to the diameter measurement.
4.
Mark the position and length of the buttohole on the fabric.
5.
Position the fabric so that the needle is on the mark that is the furthest from you.
6.
Pull the buttonhole foot towards you as far as it will go.
7.
Lower the foot.
a)
Turn the pattern selector dial to pattern no.13. Sew at moderate speed until you
reach the end mark.
b)
Turn the pattern selector dial to pattern no. 14 and sew 5-6 bartacks stitches.
c)
Turn the pattern selector dial to pattern no. 15 and sew the left side of the buttonhole
to the mark that is further from you (beginning of buttohole).
d)
Turn the pattern selector dial to pattern no. 16 and sew bartracks stitches.
Notice:
1.
When turning the pattern
selector dial, assure the
needle tip is at the upper
position, otherwise it will be
bent or damaged or fail to
sewing.
2.
When selecting the pattern
dial, set the position
correctly, otherwise it will
hurt the needle or sew over
the the selected stitch trace.
It will be different from the
selected pattern.
24
Publicidad
