Publicidad
Idiomas disponibles
Idiomas disponibles
CAUTION:
Do not use the mixer and the grater bowl at the same
time.
Mains Lead
Unwind the required mains lead from the base.
Initial Operation
Mixer function
1. The grater bowl (9) must be mounted as described in the
section "Positioning the Grater Bowl" (without tool).
2. Chop the food to be mixed into small pieces.
3. Fill the mixer vessel (3) with the food to be mixed (min. 0.2 l -
max. 1.5 l). Do not overfill! Do not exceed the maximum
quantity stated on the mixing bowl (MAX mark)! Never fill
with hot food or hard ingredients such as potatoes, ice,
coffee beans, nuts, and so on.
CAUTION: SAFETy SWITCH!
The device only works if the grater bowl (9) with lid is also
in place.
4. Put the lid (2) in place and turn it tight.
5. Close the lid with the lock (1), paying attention to the
recesses. Turn the lock until it is tight.
6. Place the mixing bowl (3) in position as described under
"Positioning the Mixing Bowl".
7. If you wish to fill in more food to be mixed you can remove
the lid and cover. Switch the device off beforehand. Remove
the lid (2) of the mixer vessel and fill with the desired ingre-
dients.
WARNING:
Do not reach into the mixer vessel, as the underlying
blade may cause injuries.
8. Place the lid on the mixer vessel again. Do not use the mixer
when empty or without the lid. Ensure that the function
switch is in the "0" position.
9. Insert the plug in a duly installed 230 V/50 Hz socket.
10. Switch the device on (Level 1 or 2 etc.) or use pulse operati-
on "P".
11. The mixing bowl must be held firmly in place during mixing.
12. For constant mixing (continuous mode):
When the device is operated on levels 1 to 4 the switch
locks into place in the respective position.
Level 1 = low rpm
Level 4 = high rpm
To switch the device off, turn the switch back to the "0"
position.
For pulse mode (mixing at brief intervals) shift the switch to
"0" position. The appliance is off now. Turn the switch to "P"
according to the desired interval length. When the switch is
released, it returns automatically to the "0" position.
13. In order to remove the mixer jug turn it counterclockwise.
14. Clean the used parts as described in "Cleaning".
05-KM 363 CB.indd 37
Mixing bowl
•
The cover of the mixer drive (4) must be mounted as descri-
bed above (Illustration 1).
•
Mount the grater bowl as described under "Positioning the
Mixing Bowl" (Illustration 2 + 3).
•
Place the locating pin over the drive shaft (Illustration 4).
The metal point faces upwards.
•
Never use more than one utensil at a time.
Dough kneading and beating
1. Please proceed as described under "Mixing Bowl Operati-
on".
2. Use the dough hook (18) for preparing the dough and attach
it to the locating pin. Press the tool down as far as it will go
(Fig. 5). Turn the tool slightly to make insertion easier.
3. Now put in your ingredients. Please note the quantity details
contained in the table below. Do not put in more or less than
the quantities stated (min. 0.2 l – max. 1.5 l).
4. Place the lid in position on the processor bowl. Turn it tight
until it is clearly heard to lock in place (Illustration 6).
5. Close the opening in the lid with the stopper (7) (Illustration
10).
6. Insert the plug into a 230 V / 50 Hz socket installed accor-
ding to existing regulations and with earthing protection.
Switch on the appliance and set a speed between 1 and 4
(See table) with switch (5).
When the device is operated on levels 1 to 4 the switch
locks into place in the respective position.
Level 1 = low rpm
Level 4 = high rpm
To switch the device off, turn the switch back to the "0"
position.
For pulse mode (Operating at short intervals) shift the switch
to "0" position. The appliance is off now. Turn the switch to
"P" according to the desired interval length. When the switch
is released, it returns automatically to the "0" position.
With this device it is possible within a very short time:
•
up to 1000 g of heavy dough (bread or pastry),
•
to stir up to 1 litre of crepe or waffle dough,
•
beat up to 1500 g of light dough (e.g. for cookies).
NOTE:
Do not exceed the short operation times stated in the table
when kneading the dough!
7. After kneading/stirring turn the switch (5) back to position
"0" as soon as a small amount or ball of dough has formed.
Then remove the mains plug.
8. To remove the lid, turn it in an anticlockwise direction.
9. Pull the blade off from the locating pin.
10. Remove the locating pin from the drive shaft.
11. In order to remove the mixing bowl, turn it in an anticlock-
wise direction. You can release the finished dough with the
dough scraper (23) and remove it from the bowl.
12. Clean the used parts as described in "Cleaning".
37
26.08.2009 14:19:55 Uhr
Publicidad
