IMG STAGELINE LED-300DX/RGB Manual De Instrucciones página 9

3 Applications
The light effect unit is suited for applications on stage,
in discotheques or party rooms. Its light source is a
super bright LED (3 W) with a low power consumption
and a long life.
The light effect unit is designed for control via a
DMX light controller (LED-300DX/RGB with 3 DMX
control channels, LED-300DX/WS with 2 control chan-
nels); however, it can also be operated on its own or
with the remote control LC-3 available as an acces-
sory.
4 Mounting
G
Always place the unit in such a way that a sufficient
air circulation will be ensured during operation.
Never cover the air vents on the housing.
G
The minimum distance to the illuminated object
should be 10 cm.
1) For mounting the light effect unit, fasten the two
mounting brackets (1) via four screws to a suitable
place.
2) For suspended mounting of the unit at a cross bar
or a lighting stand, screw the mounting angle pro-
vided via two screws to the two mounting brackets
(1). Screw the mounting angle with the unit to the
cross bar or to the lighting stand.
WARNING Mount the light effect unit safely and
expertly. If it is installed at a place
where people may walk or sit under
it, additionally secure it (e. g. by a
safety rope; fasten the safety rope in
such a way that, even in the event of
a fall, the maximum falling distance
of the light effect unit will not exceed
20 cm).
5 Setting the Light Effect Unit
into Operation
WARNING Never look directly into the light beam;
this may cause eye damage.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
To switch on the unit, connect the plug of the mains
cable (7) to a mains socket (230 V~/50 Hz). To switch
it off, disconnect it from the socket.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket which is
switched on and off via a light switch.
Caution: Do not connect the unit to the mains voltage
via a dimmer!
6 Operation without Controller
Set DIP switch No. 1 (8) to ON; set all other DIP
switches to the lower position. The indicating LED (9)
will light up.
Fig. 4 Adjustment of the master mode
If the light effect unit does not receive any DMX control
signal, the light beams will light up. The dome will start
rotating, occasionally changing its sense of rotation.
Model LED-300DX/RGB will additionally change the
colour of the light beams.
When music is played at sufficient volume with a
clear rhythm in the bass range, the sense of rotation,
the speed, the change of colour (for LED-300DX/RGB
only) and the activation/deactivation of the light beams
(for LED-300DX/WS only) will be controlled via the
internal microphone (5). With each music control
pulse, the indicating LED (9) will shortly be extin-
guished. If the music control should not work optimally,
increase the volume or reduce the distance between
the sound source and the light effect unit.
6.1 Constant sense of rotation and speed
For turning the dome at a constant speed in one direc-
tion, also set DIP switch No. 2 (8) to ON. Now it will be
possible to adjust the sense of rotation with DIP switch
No. 3 and the speed with the DIP switches Nos. 4, 5,
6. The music control via the microphone (5) will be
deactivated.
6.2 Interconnecting several LED-300DX units
Several LED-300DX/RGB or LED-300DX/WS units
may be interconnected in order to control all slave
units to the same rhythm via the microphone of the
master unit.
1) Connect the DMX OUTPUT (3) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (2) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
3) On the slave units, set all DIP switches Nos. 1 – 9
(8) to the lower position (OFF). Once the slave units
receive the control signals of the master unit, the
indicating LED (9) of the slave units will shortly light
up every 2 seconds.
Fig. 5 Adjustment for the slave units (slave mode)
GB
9