Publicidad
Idiomas disponibles
Idiomas disponibles
• use clamps or another practical way to secure and support the workpiece to
a stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to loss of control.
• keep your body positioned to either side of the blade, but not in line with the
saw blade. KICKBACK could cause the saw to jump backwards (see causes and
operator Prevention of kickback and kIckBAck).
• Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.
• Always make sure nothing interferes with the movement of the lower blade guard.
• Accessories must be rated for at least the speed recommended on the tool warning
label. Wheels and other accessories running over rated speed can fly apart and cause injury.
Accessory ratings must always be above tool speed as shown on tool nameplate.
• Always make sure the saw is clean before using.
• Stop using this saw and have it properly serviced if any unusual noise or abnormal
operation occurs.
• Always be sure all components are mounted properly and securely before using tool.
• Always handle the saw blade with care when mounting or removing it or when
removing the diamond knockout.
• Always wait until the motor has reached full speed before starting a cut.
• Always keep handles dry, clean and free of oil and grease. Hold the tool firmly with
both hands when in use.
• Always be alert at all times, especially during repetitive, monotonous operations.
• Always be sure of position of your hands relative to the blade.
• Stay clear of end pieces that may fall after cutting off. They may be hot, sharp and/or
heavy. Serious personal injury may result.
• Replace or repair damaged cords. Make sure your extension cord is in good
condition. Use only 3-wire extension cords that have 3-prong grounding-type plugs
and 3-pole receptacles that accept the tool's plug.
• An extension cord must have adequate wire size (AWG or American Wire
Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity
of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord
will cause a drop in line voltage resulting in loss of power and overheating. When
using more than one extension to make up the total length, be sure each individual
extension contains at least the minimum wire size. The following table shows the
correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller the gauge number, the heavier the
cord.
Recommended Minimum Wire Size for extension cords
total length of cord
25 ft.
50 ft.
7.6 m
15.2 m
Wire Size AWG
18
WARNING:
WARNING:
conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of
use, noise from this product may contribute to hearing loss.
WARNING:
must wear proper eye protection that conforms to ANSI Z87.1.
WARNING:
safety glasses. Also use face or dust mask if cutting operation is dusty.
ALWAYS wear certified safety equipment:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3).
• ANSI S12.6 (S3.19) hearing protection.
• NIOSH/OSHA respiratory protection.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known in the state of California to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints, crystalline silica from bricks and cement and other
75 ft.
22.9 m
18
16
Blades coast after turn off. Serious personal injury may result.
AlWAyS wear proper personal hearing protection that
AlWAyS use proper eye protection. All users and bystanders
AlWAyS uSe SAfety GlASSeS. Everyday eyeglasses are NOT
100 ft.
125 ft.
30.5 m
38.1 m
16
14
5
150 ft.
175 ft.
45.7 m
53.3 m
14
12
Publicidad
