TEFAL PerfectMix BL88A8 Manual De Instrucciones página 50

SAFETY INSTRUCTIONS
CAUTION: the safety precautions are part of the
appliance. Read them carefully before using your
new appliance for the first time. Keep them in a
place where you can find and refer to them later on.
DESCRIPTION
A Motor unit
B "Smoothie" button
C "Ice crush" button
D "Auto clean" button
E Control knob
F / O Blender jug assembly
F1 / O1 Blade unit
F2 / O2 Locking ring
F3 / O3 Seal
F4 / O4 Graduated blender jug
F5 / O5 Lid
F6 / O6 Lid cap
G Min speed
H Max speed
BEFORE THE FIRST USE
• Clean all the parts (F, J, K, L, M, O) with warm water and washing up
liquid except for the motor unit (A) which must never be immersed in
water or placed under running water (see section Cleaning).
CAUTION: The blades are extremely sharp; handle them with caution
when using or cleaning the appliance.
• Handle the glass jar (F4) with caution when using and cleaning, do not
drop.
• Make sure all the packaging has been removed before operating the
appliance.
• Important note: Turn the control knob (E) to
blender jug (F/O) on the motor unit (A).
94
I Pulse button
J Spatula* (accessory depending
on model)
K Herb chopper* (accessory
depending on model)
K1 Seal
K2 Herb chopper blade unit
L Spice grinder* (accessory
depending on model)
L1 Seal
L2 Spice grinder blade unit
M Herb chopper and Spice grinder
bowl* (accessory depending on
model)
before placing the
• Make sure the evacuation hole on the motor block (A) is not blocked by
food or other things when using
• The appliance will start only if the blender jug is locked correctly on the
motor unit.
• Do not operate the appliance if the lid is not in place.
ASSEMBLING AND FITTING THE JUG
Moisten the seal (F3, O3) (even if already fitted on the blade unit
(F1, O1)). Be careful to correctly fit the seal (F3, O3) back onto the blade
unit (F1, O1) the correct way up (Fig 17).
• Check the seal is in place on the blade unit.
• Place blade unit on the locking ring (Fig 1, Fig 7).
• Turn the jug upside down and place blade unit with locking ring on the
base.
• Make sure the locking ring is locked correctly : the two arrows must be
aligned (Fig 3, Fig. 9).
• Add the ingredients to the assembled jug without exceeding the
maximum level indicated:
* 1.5 L for thick mixtures
* 1.25 L for liquid preparations
Warning : Do not pour boiling liquids (over 80°C/176°F) into the jug.
Do not insert any metallic object into the blender. Do not mix pieces
of frozen ingredients larger than 25x25x25mm.
• Fit the lid (F5, O5) on the jug (Fig. 6, Fig. 12). To avoid any splashes
during blending make sure that the curved tabs on the lid are aligned
with the spout and handle (Fig. 5, Fig. 11) . Fit the measuring cap (F6,
O6) in the hole on the lid (Fig. 8). Then position the bowl on the motor
unit and turn it 1/4 turn clockwise (Fig 4 / Fig 10)
USING YOUR BLENDER
• Once the blender jug is locked correctly on the motor unit, plug in the
appliance. The lights on the appliance flash twice and you hear a beep.
Turn it on using the desired function.
• Speed selection: Turn the control knob (E) to choose the desired speed;
the speed increases gradually between min and max. The intensity of
the lights on the appliance increase gradually as the speed increases.
You can change the speed as required during preparation.
EN
95