Publicidad
Idiomas disponibles
Idiomas disponibles
Select Custom Settings
To display current settings tap the Timeout (
or PIR Sensitivity (
P
) button. The indicator LED (
illuminate.
• Timeout and Sensor Mode settings may have different settings for each circuit. In this case, the LED for
Circuit 1 settings will illuminate, followed by the LED for Circuit 2 settings.
Change Settings
1
Press and hold the desired programming button (
to flash (about 3 seconds). This will change settings for BOTH circuits.
• Timeout (
) and Sensor Mode (
M
) may be adjusted independently for EACH circuit. Holding
M
AND
T
or
T
simultaneously will program settings for that specific circuit.
1
2
2
Tap the same programming button to cycle to your desired setting.
3
Press and hold the same programming button until the
selection (about 3 seconds).
Default settings are shown
in bold
IL
Indicator LEDs
1
Timeout Button
30 minutes
15 minutes
5 minutes
1 minute
30
15
Sensor Mode Button
1
5
1
2
Occupancy
(Auto-ON / Auto-OFF)
Occupancy with Learning ALD
3
Mode
Occupancy with Fixed ALD
4
Occ
2
Vacancy
(Manual-ON / Auto-OFF)
Lrn
Fixd
M
Vac
Sensor LED
(behind lens) Pulses green for
ultrasonic and amber for PIR
detection during Test mode.
M
1
Using ONLY the
or
to enter programming mode will set BOTH circuits to the new setting. Holding
and
or
simultaneously will program settings for that specific circuit.
T
T
1
2
2
Circuit 1 Default : Occupancy ;Circuit 2 Default : Vacancy
3
ALD (Ambient Light Detection) Learn mode will turn lights on only if natural light in room is low. If switch turns on
when there is enough natural light, or if switch does not turn on when there is not enough natural light, press the tap
button within 5 seconds of entering the room. Over time, the switch will learn your preferred setting. If both circuits
are set to Occ with Learning ALD mode, they will learn the SAME threshold.
4
ALD (Ambient Light Detection) Fixed mode will turn the lights on only if natural light in room is low. The light level
at which lights will automatically turn on (or stay off) can be adjusted through the "Set ALD Fixed Level" setting in
"Additional Settings" section.
Technical Assistance: www.lutron.com
®
M
), Sensor Mode (
), Ultrasonic Sensitivity (
)that corresponds to the current setting will
IL
,
,
or
) until an
M
P
goes solid to lock your
IL
Circuit 1
Tap button
(tap on / off)
Circuit 2
Tap button
(tap on / off)
Ultrasonic Sensitivity Button
High
m
Hi
Medium
Med
Low
Low
Off
Off
PIR Sensitivity Button
PIR
High
Hi
Medium
Med
Low
Low
Min
Minimum
Ultrasonic
Transducers
PIR Lens
U.S.A., Canada, Caribbean: 1.800.523.9466
|
Additional Settings
Note: Additional product information, including "Circuit Swapping", and other programming
),
options and wiring diagrams are available at www.lutron.com/DTMaestroInstall
Test Mode:
Test Mode is a short timeout (less than 15 seconds) that will test the sensor's coverage with
the current settings.
To enable Test Mode:
1. Press and hold either
begins
IL
2. The device will exit Test Mode automatically after 5 minutes of inactivity, or when any button
is pressed.
or
Note: An amber LED flashes to indicate PIR detection, a green LED flashes to indicate
ultrasonic detection. You may hold
current sensitivity of that specific technology.
Restore Default Settings:
Press and hold
the sensor's settings back to their defaults.
Off-While-Occupied:
When Off-While-Occupied is Enabled: After manual shutoff, the sensor will keep lights off
T
as long as the space is occupied and the timeout has not expired. This setting is best for
1
rooms where presentations are given and lights may be kept off during occupancy. This is the
default setting.
When Off-While-Occupied is Disabled: After manual shutoff, the sensor will keep lights off
T
for 25 seconds before looking for motion. If motion is detected, the lights will turn back on.
2
This setting is best for high-traffic areas like bathrooms and hallways.
Change Setting:
1. Press and hold
P
2. Tap
to cycle to your desired setting.
3. Press and hold
IL
Off-While-Occupied Disabled
P
Off-While-Occupied Enabled (Default)
Setting Fixed ALD Level:
1. a. For Circuit 1: Press and hold
3 seconds).
b. For Circuit 2: Press and hold
3 seconds).
2. The Ambient Light Detect light level will now be displayed on the
M
or
your desired setting.
3. Press and hold
Light Level
IL
High - turns lights ON unless room is very bright
Medium
Low (Default when in ALD Fixed mode)
Minimum - turns lights ON only when room is dark
Mexico: +1.888.235.2910
|
T
or
T
until the PIR lens flashes (about 7 seconds).
1
2
P
or
for 2 seconds while in test mode to test the
P
and
until all
blink slowly (about 7 seconds). This will restore ALL of
IL
P
and
at the same time until an
IL
P
until the
goes solid to lock your selection.
IL
M
and
until the
and
until the
M
P
until the
goes solid to lock your selection.
M
IL
Others: +1.610.282.3800
|
begins to flash (about 3 seconds).
begins to flash (about
IL
begins to flash (about
IL
. Tap
to cycle to
IL
M
Publicidad
