switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the red light
continuously flashing a short ON followed by a longer ON
(see charger for blink pattern). Once the battery pack has
reached an appropriate temperature, the charger will resume
the charging procedure.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and remove
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Removing Dust Bowl (Fig. C)
1. Remove the dust bowl
release button
2
and pulling the dust bowl down and out.
Shock hazard. Disconnect the
To reduce the risk of
3
by pressing the dust bowl
Installing Dust Bowl (Fig. C)
1. Install the dust bowl
audible click. Ensure the dust bowl is secured in place
before using.
Installing Accessories (Fig. D)
1. The crevice tool
7
allows for vacuuming in narrow and
hard to‑reach places.
2. To attach an accessory, press the accessory into dust bowl
3. The crevice tool
7
can be stored on the unit as shown in Fig D.
OPERATION (FIG. A)
WARNING:
ELECTRIC SHOCK – USE INDOORS ONLY.
WARNING:
serious personal injury, turn unit OFF before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
WARNING:
Never use the vac without its filter.
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
6
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
On/Off Switch (Fig. F)
nOTE: This product is for dry pick‑up only.
•
To switch the vac on, slide the On/Off switch
•
To switch the vac off, slide the On/Off switch
MAINTENANCE
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
3
onto the unit and listen for an
TO REDUCE THE RISK OF
To reduce the risk of
Projectile/Respiratory Hazard:
5
into the tool handle, align the
1
1
To reduce the risk of serious
English
3
.
forward.
back.
7