Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
ENGLISH
Getting Started
Getting Started
Introduction
Introduction
This manual provides operation instructions and information required to
operate the Maverick Tire Changer.
Maintaining records of personnel trained is solely the responsibility of the
owner and management.
This manual assumes the technician has already been trained in basic tire
changing procedures.
Corporate Information
Corporate Information
Hunter Engineering Company
www.hunter.com
For Your Safety
For Your Safety
Hazard Definitions
Watch for these symbols:
Hazards or unsafe practices, which could result in minor
personal injury or product or property damage.
Hazards or unsafe practices, which could result in severe
personal injury or death.
Immediate hazards, which will result in severe personal
injury or death.
These symbols identify situations that could be detrimental to your safety and/
or cause equipment damage.
Important Safety Instructions - Electrical
Do not operate equipment with a damaged cord or equipment that has been
dropped or damaged until examined by a Hunter Service Representative.
If an extension cord is necessary, it must have a current rating equal to or
more than that of the equipment. Cords rated for less may overheat. Arrange
the cord so that it will not be tripped over or pulled.
Never use the cord to pull the plug from the outlet. Do not let cord hang over
any edge or contact fan blades or hot manifolds.
Verify that the electrical supply circuit and the receptacle are properly
grounded.
To reduce the risk of electrical shock, do not use on wet surfaces or expose
to rain.
Verify the appropriate electrical supply circuit is the same voltage and
amperage ratings as marked on the equipment before operating.
DO NOT ALTER THE ELECTRICAL PLUG. Plugging the
electrical plug into an unsuitable supply circuit will damage the
equipment and may result in personal injury.
When servicing the Maverick, power must be disconnected by removing the
power cord from the electrical outlet. Ensure that the Maverick power switch
is in the off position ("O" position) before plugging the power cord into the
electrical power outlet.
Important Safety Instructions - Operation
To reduce the risk of fire, do not operate equipment near open containers
of flammable liquids (gasoline). Read and follow all caution and warning
labels affixed to your equipment and tools. Misuse of this equipment
can cause personal injury and shorten the life of the equipment. Keep
all instructions permanently with the unit. Keep all decals, labels, and
notices clean and visible. To prevent accidents and/or damage to the Tire
Changerrecommended accessories. Use equipment only as described in
this manual. Never stand on the Tire Changer. Wear non-slip safety footwear
when operating the Tire Changer. Keep hair, loose clothing, neckties, jewelry,
fingers, and all parts of body away from all moving parts. ALWAYS WEAR
OSHA APPROVED SAFETY GLASSES. Eyeglasses that have only impact
resistant lenses are NOT safety glasses.
Important Safety Instructions - Tire Changer
Read and follow all caution and warning labels affixed to equipment and tools.
Read and understand all instructions before operating this machine.
English
Do not exceed these pressure limitations:
SUPPLY LINE PRESSURE (from compressor) 175 PSI (12 bar)
OPERATING PRESSURE (gauge on regulator) 145 PSI (9.9 bar)
BEAD SEATING PRESSURE (gauge on screen) 40 PSI (2.8 bar)
Never mount a tire to a rim that is not the same diameter
(e.g., 16 1/2 inch tire mounting on a 16 inch rim.
After loss of air line pressure ALWAYS raise the wheel lift
pedal to prevent the wheel lift from rising quickly during
first operation.
Activate blast inflation nozzle only when seating bead.
Bleed air pressure from the system before disconnecting air supply line
or other pneumatic components. Air is stored in a reservoir for operation
of the inflation components. Air pressure can be bled from the system by
pulling up on the knob located on the top of the regulator, and then turning it
counterclockwise.
Do not activate the blast inflation nozzle if the tire is not properly clamped.
Do not operate TC with worn rubber or plastic parts. Wheels equipped with
low tire pressure sensors or specil tire and rim design may require certain
procedures. Consult manufacturer's service manuals.
Power Source Precaution
Power Source Precaution
The Maverick is intended to operate from a power source that will apply
230VAC +10% / -15%, 1 phase, 20 amp 50/60 Hz power, power cable includes
NEMA 20 amp plug, L6-20P, between the supply conductors of the power
cord.
A protective ground connection, through the grounding
conductor is the power cord, is essential for safe operation.
Use only a power cord that is in good condition.
Equipment Specifications
Equipment Specifications
Electrical (North America)
TCM - SITE REQUIREMENTS
Voltage:
Air Supply Requirements
Weight
Width (W)
Height (H)
Depth (D1 / D1w)
Depth (D2 / D2w)
TCM - KEY SPECIFICATIONS
Mount / Demount Tool
Clamping Type
Bead Loosening Type
Match Mounting Capable
Rim Diameter Range
Maximum Tire Diameter
Maximum Wheel Width
Drive
Image 1.
208-230 VAC, 1 Ph, 3 kW. NEMA L6-20
plug provided
8.6 ± 1.7 bar
TCM: 476 kg / TCMW: 499kg
1346 mm
1955mm
1168 mm) / 1448 mm
1524 mm / 1803 mm
Polymer Leverless
Center w/ Quick Clamp
Upper / Lower Roller
Yes
254 mm - 863 mm
1270 mm
381 mm
Variable up to 17 rpm CW / CCW
Torque: 700 ft-lbs (949 Nm)
Image 2.
7
Publicidad
