Kärcher NT 30/1 Tact Te H Manual De Instrucciones página 17

Installing the dust bag
1. Unlock and remove the suction head.
2. Insert the dust bag.
Illustration E
3. Pull the dust bag over the container. Ensure that the
marking line is within the container and the ventila-
tion hole is positioned on the back wall of the con-
tainer.
4. Fit and lock the suction head.
Wet vacuum cleaning
DANGER
Danger from dust that is harmful to your health
Respiratory sicknesses through inhalation of dust.
No dusts harmful to health may be vacuumed when per-
forming wet vacuum cleaning.
Installing the squeegees
1. Remove the brush strip.
Illustration F
2. Install the squeegees.
Closing the suction connection
1. Fit a plug exactly into the suction connection.
Illustration G
2. Push the plugs in until they engage.
Removing the safety filter bag
● The safety filter bag must always be removed when
vacuuming wet substances.
1. Unlock and remove the suction head.
2. Pull safety filter bag on the flange up and out.
Illustration H
3. Seal the suction connection opening of the safety fil-
ter bag tightly with a sealing cap.
4. Fold up the safety filter bag.
Illustration I
5. Take off the protective film and close the ventilation
hole (1x NT 30/1 - 2x NT 40/1, NT 50/1) with a self-
adhesive tab.
Illustration J
6. Close the safety filter bag tightly with the attached
cable tie.
7. Remove the safety filter bag.
8. Clean the container inside with a moist cloth.
9. Dispose of used safety filter bag in dust-tight bag in
accordance with statutory regulations.
10. Fit and lock the suction head.
Removing the dust bag
● The dust bag must always be removed when vacu-
uming wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag.
Illustration K
3. Take off the protective film and close the ventilation
hole with a self-adhesive tab.
4. Seal the dust bag tightly underneath the opening us-
ing cable ties.
5. Remove the dust bag.
6. Clean the container inside with a moist cloth.
7. Dispose of the dust bag in accordance with statutory
regulations.
8. Fit and lock the suction head.
Draining the waste water
NT 50/1 only:
1. Drain the waste water via the drain hose.
Illustration L
● We recommend switching off the "Automatic filter
dedusting" function when vacuuming wet dirt with
the crevice nozzle or the upholstery nozzle (option-
al), or when sucking mainly water out of a container.
● The device switches off automatically when the
maximum fluid level is reached.
● When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not au-
tomatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
● On completion of wet vacuum cleaning: Clean the
flat fold filter using the dedusting function. Clean the
electrodes with a brush. Clean the container with a
moist cloth and dry it off.
The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 35 mm can be
connected.
Illustration M
Device OFF
● Device ON
● Automatic filter dedusting: OFF
● Adjust the suction performance (min-
● Device ON
● Automatic filter dedusting: ON
● Adjust the suction performance (min-
Switching on the device
1. Connect the mains plug.
2. Set the turn switch to the desired program.
Working with power tools
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for direct connection of pow-
er tools to the vacuum cleaner. Any other use of the
socket is prohibited.
1. Plug the mains plug of the power tool into the power
socket on the vacuum cleaner. The vacuum cleaner
is in Standby mode.
2. Switch on the device at the turn switch.
Note
The vacuum cleaner is automatically switched on and
off with the power tool.
Note
The vacuum cleaner has a startup delay of up to 0.5
seconds and an after-running time of up to 15 seconds.
Note
See the Technical data for the permissible power rating
of the power tool.
3. Remove the angle piece from the suction hose.
Illustration N
4. Install the tool adapter on the suction hose.
5. Connect the tool adapter to the power tool.
Illustration O
English
General
Clip connection
Operation
Turn switch
max)
max) (eco = energy-saving mode)
17