Ego Power+ CS1614E Manual De Instrucciones página 4

◾
Store idle power tools out of the reach of children and
EN
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
◾
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect
the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
◾
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
◾
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
◾
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces may lead to unsafe handling and/or
loss of control of the tool.
BATTERY TOOL USE AND CARE
◾
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
◾
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
◾
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
◾
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
◾
Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
◾
Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130°C may cause explosion.
4
CORDLESS CHAIN SAW
◾
Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
◾
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
◾
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
CHAIN SAW SAFETY WARNINGS
◾
Keep all parts of the body away from the saw chain
when the chain saw is operating. Before you start
the chain saw, make sure the saw chain is not
contacting anything. A moment of inattention while
operating chain saws may cause entanglement of your
clothing or body with the chain.
◾
Always hold the chain saw with your right hand
on the rear handle and your left hand on the front
handle. Holding the chain saw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
◾
Hold the chain saw by insulated gripping surfaces
only, because the saw chain may contact hidden
wiring. Saw chains contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
◾
Wear eye protection. Further protective equipment
for hearing, head, hands, legs and feet is
recommended. Adequate protective clothing will
reduce personal injury by flying debris or accidental
contact with the saw chain.
◾
Do not operate a chain saw in a tree, on a ladder,
from a rooftop, or any unstable support. Operation
of a chain saw in this manner could result in serious
personal injury.
◾
Always keep proper footing and operate the chain
saw only when standing on fixed, secure and level
surface. Slippery or unstable surfaces such as ladders
may cause a loss of balance or control of the chain
saw.
◾
When cutting a limb that is under tension be alert
for spring back. When the tension in the wood fibers
is released the spring loaded limb may strike the
operator and/or throw the chain saw out of control.