Toro Flex-Force Power System 60V Manual De Instrucciones página 6

1 type of battery pack may create a risk of fire
when used with another battery pack.
7. Charge the battery pack in a well-ventilated area
only.
8. Follow all charging instructions and do
not charge the battery pack outside of the
temperature range specified in the instructions.
Otherwise, you may damage the battery pack
and increase the risk of fire.
9. Do not operate the tool without all guards and
other safety protective devices in place and
functioning properly on the tool.
10. Dress properly—Wear appropriate clothing,
including eye protection; long pants; substantial,
slip-resistant footwear; rubber gloves; and
hearing protection. Tie back long hair and do
not wear loose clothing or loose jewelry that can
get caught in moving parts. Wear a dust mask in
dusty operating conditions.
III. Operation
1. Avoid dangerous environments—Do not use the
tool in rain or in damp or wet locations.
2. Use the proper tool for your application—Using
the tool for purposes other an its intended use
could prove dangerous to you and bystanders.
3. Prevent unintentional starting—Ensure that the
switch is in the O
to the battery pack and handling the tool. Do
not carry the tool with your finger on the switch
or energize the tool with the switch in the O
position.
4. Operate the tool only in daylight or good artificial
light.
5. If the tool strikes an object or starts to vibrate,
immediately shut off the tool, wait for all moving
parts to stop, and disconnect the battery before
examining the tool for damage. Make all
necessary repairs before resuming operation
6. Remove the battery pack from the tool before
adjusting it or changing accessories.
7. Keep your hands and feet away from the cutting
area and all moving parts.
8. Shut off the tool, remove the battery pack from
the tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
9. Remove the battery pack from the tool whenever
you leave it unattended.
10. Do not force the tool—Allow the tool to do the
job better and safer at the rate for which it was
designed.
11. Do not overreach—Keep proper footing and
balance at all times, especially on slopes. Walk,
never run with the tool.
position before connecting
FF
12. Stay alert—Watch what you are doing and use
common sense when operating the tool. Do not
use the tool while ill, tired, or under the influence
of alcohol or drugs.
13. Ensure that the ventilation openings are kept
clear of debris.
14. Under abusive conditions, the battery pack may
eject liquid; avoid contact. If you accidently
come into contact with the liquid, flush with
water. If the liquid contacts your eyes, seek
medical help. Liquid ejected from the battery
pack may cause irritation or burns.
15. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or
temperature above 130°C (265°F) may cause
explosion.
16. CAUTION—A mistreated battery pack may
present a risk of fire, explosion, or chemical
burn.
•
Do not disassemble the battery pack.
•
Replace the battery pack with a genuine
Toro battery pack only; using another type of
battery pack may cause a fire or risk of injury.
•
Keep battery packs out of the reach of
children and in the original packaging until
you are ready to use them.
IV. Maintenance and Storage
1. Maintain the tool with care—Keep it clean and
N
in good repair for best performance and to
reduce the risk of injury. Follow the instructions
for lubricating and changing accessories. Keep
handles dry, clean, and free from oil and grease.
2. When the battery pack is not in use, keep it
away from metal objects such as paper clips,
coins, keys, nails, and screws that can make a
connection from 1 terminal to another. Shorting
the battery terminals may cause burns or a fire.
3. Keep your hands and feet away from moving
parts.
4. Shut off the tool, remove the battery pack from
the tool, and wait for all movement to stop before
adjusting, servicing, cleaning, or storing the tool.
5. Check the tool for damaged parts—If there
are damaged guards or other parts, determine
whether it will operate properly. Check for
misaligned and binding moving parts, broken
parts, mounting, and any other condition that
may affect its operation. Unless indicated in the
instructions, have an Authorized Service Dealer
repair or replace a damaged guard or part.
6. If the blade becomes worn, bent, or damaged,
replace it; contact an authorized Toro distributor.
4