Publicidad
Idiomas disponibles
Idiomas disponibles
1.- Mixer inputs:
a.- MIC: microphone input, use the channel GAIN control to change the input sensitivity,
a
MIC
b
b.- LINE: line input, use the channel GAIN control to change the input sensitivity, 6.3 mm
LINE
c.- GAIN: input gain control. For the MIC microphone input (XLR) the range is from +20 dB
GAIN
c
0
+20
+64
-6
+38
d
HIGH
d.- HIGH: high pass filter with 12 kHz cut-off frequency.
e.- MID: band pass filter with a centre frequency of 2.5 kHz.
MID
e
f.- LOW: low pass filter with 80 Hz cut-off frequency.
LOW
f
g.- FX (DSP)/SEND: channel send selector to the FX (DSP) integrated effects processor
g
FX(DSP)
SEND
h
h.- Volume control of signal to be sent to FX (DSP) or SEND, depending on the FX (DSP)/
i
L
R
PAN
j
i.- PAN: control that adjusts the stereo image in the final mix.
MUTE
k
CLIP
10
j.- MUTE: button that allows you to mute this channel which is sent to the SEND bus or
5
0
5
k.- CLIP: LED which lights up when the input signal level is too high. In this case, decrease
l
10
20
30
40
l.- Input channel volume slider.
50
60
2.- Input and output connectors:
a
MIC
b
LINE
a.- RETURN: stereo input for external effects processor with independent volume control, 2 x 6.3 mm
GAIN
c
0
jack balanced connectors. If you only insert the L connector, the audio received by the mixer will
+20
+64
-6
+38
be distributed by L and R of the MAIN MIX output; if you connect both channels of the RETURN
d
HIGH
input, L and R, each channel will go to its respective L or R output of the MAIN MIX output.
e
MID
b.- SEND: line level output with independent volume control, 6.3 mm jack connector. This output will
receive signal from channels with the FX (DSP)/SEND selector pressed in. Connect this output
LOW
f
to an external effects processor and the output signal from this will return to the mixer via the
g
FX(DSP)
SEND
RETURN input.
h
c.- PHONES
i
L
R
d.- MAIN MIX: MAIN MIX bus line level outputs, 2 x RCA, 2 x 6.3 mm jack and 2 x XLR connectors.
PAN
j
MUTE
k
CLIP
10
5
0
5
l
10
20
30
40
50
60
a
balanced XLR connector. It is possible to connect condenser microphones. For this
SEND
purpose, the phantom power must be switched on with the PHANTOM +48 V button.
b
c
jack unbalanced.
to +64 dB, and for the LINE input (6.3 mm jack) from -6 dB to +38 dB.
a
or to the SEND bus.
b
SEND selection button.
c
d e
f
to the FX integrated effects processor (DSP).
g
the input level by GAIN control until the LED turns off or turns on occasionally.
h
i
L
a
SEND
b
c
a
b
: headphone output for monitoring, 6.3 mm stereo jack.
c
d e
f
g
h
i
RETURN
MAIN MIX
L
R
L
R
L
PHONES
L
R
R
PROGRAM
MODE
REC
HIGH
PHONES
PARAMETER
VOL
LOW
RETURN
SEND VOL
VOL
MUTE
10
10
10
5
5
5
0
0
0
5
5
5
10
10
10
20
20
20
30
30
30
40
40
40
50
50
50
60
60
60
L
RETURN
MAIN MIX
FX (DSP)
PLAYER
L
R
R
L
PHONES
L
R
R
PROGRAM
MODE
REC
HIGH
PHONES
PARAMETER
VOL
LOW
RETURN
SEND VOL
VOL
MUTE
10
10
10
5
5
5
0
0
0
5
5
5
10
10
10
- 3 -
20
20
20
30
30
30
40
40
40
50
50
50
d
s
r
q
PHANTOM
o p
+48 V
+6
n
+2
m
0
-4
-7
l
L
R
k
10
5
0
j
5
10
20
30
40
50
60
R
MAIN MIX
d
s
r
q
PHANTOM
o p
+48 V
n
+6
+2
m
0
-4
-7
l
L
R
k
10
5
0
j
5
10
20
30
40
50
EN
Publicidad
