Publicidad
Idiomas disponibles
Idiomas disponibles
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
• Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
CORING EQUIPMENT
•When performing drilling that requires the use of
water, route the water away from the operator's
work area or use a liquid collection device. Such
precautionary measures keep the operator's work
area dry and reduce the risk of electrical shock.
•Operate power tool by insulated grasping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
•Wear hearing protection when diamond drilling.
Exposure to noise can cause hearing loss.
•When the bit is jammed, stop applying downward
pressure and turn off the tool. Investigate and
take corrective actions to eliminate the cause of
the bit jamming.
•When restarting a diamond drill in the workpiece
check that the bit rotates freely before starting.
If the bit is jammed, it may not start, may overload
the tool, or may cause the diamond drill to release
from the workpiece.
•When securing the drill stand with anchors and
fasteners to the workpiece, ensure that the an-
choring used is capable of holding and restraining
the machine during use. If the workpiece is weak
or porous, the anchor may pull out causing the drill
stand to release from the workpiece.
•When securing the drill stand with a vacuum pad
to the workpiece, install the pad on a smooth,
clean, non-porous surface. Do not secure to
laminated surfaces such as tiles and composite
coating. If the workpiece is not smooth, flat or well
affixed, the pad may pull away from the workpiece.
•Ensure there is sufficient vacuum before and
during drilling. If the vacuum is insufficient, the
pad may release from the workpiece.
•Never perform drilling with the machine secured
by the vacuum pad only, except when drilling
downwards. If the vacuum is lost, the pad will
release from the workpiece.
•When drilling through walls or ceilings, ensure
to protect persons and the work area on the
other side. The bit may extend through the hole or
the core may fall out on the other side.
•Never use this product for overhead drilling.
• Always use expansion-type anchor to hold stand
on cracked, uneven, porous, or vertical surfaces.
• Do not operate tool with carrier above line marked
on mast. Tool and stand could become unsecure
and tip over during use causing serious injury.
• Chemical Burn Hazard. Keep coin cell battery
away from children.
•
To reduce the risk of injury in ap-
WARNING
plications that produce a consid-
erable amount of dust, use an OSHA compliant
dust extraction solution in accordance with the
solution's operating instructions.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SPECIFICATIONS
Drill Cat. No. .............................................MXF302
Battery Type ........................................ MX FUEL™
Charger Type....................................... MX FUEL™
Module/FCC ID ............................ BGM11S/QOQ11
Rated No Load RPM ................................... 0-2200
Maximum Bit Capacity ....................................... 14"
Spindle Thread ...........................................1-1/4"-7
Maximum Inlet Pressure ................................ 90 psi
Recommended Ambient
Operating Temperature ......................0°F to 125°F
Stand Cat. No. ................................................3302
Compatible With Drill ................................. MXF301
Mounting Plate Cat. No. .................................3315
3
Publicidad
