Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always secure the stand to the work surface to
help prevent personal injury and to protect the
stand. Do not rely on the weight of the stand,
shoring pin alone or body weight on the stand for
securing during use. An unsecured stand could
rotate during coring and possibly cause injury.
NEVER attempt to use body weight to hold stand.
NEVER rely on the shoring pin alone for securing.
Using an Expansion-Type Anchor
Expansion-type anchors is the preferred method
used for floor coring. Use a 5/8" or 3/4" expansion an-
chor with an integral threaded rod, washer, and nut.
1. Remove battery pack from the drill and the stand
storage position, move the stand aside.
2. Mark the hole location and measure out 16" to 20",
in the direction the stand will be set.
3. Set the anchor according to the expansion-type
anchor manufacturer instructions.
4. Place the stand over the anchor so the rod extends
through the anchor plate.
5. Place the center hole indicator tool into the center
hole indicator tool attachment slot and align the
appropriate hole over the desired hole location.
6. Thread the nut onto the rod, and tighten securely.
7. Adjust all eye bolts (4) to ensure the stand is level
according to the bubble indicator.
Eye
bolts
Hole center tool attachment
Using a Vacuum Pad and Pump
Install the Vacuum Pad and Pump according to the
manufacturer's instructions.
1. Loosen the eye bolts (4) until they are flush with
the drill stand.
2. Place the stand on the vacuum base plate with the
main anchor extending through the anchor plate.
3. Thread the nut onto the rod, and tighten securely
4. Level the stand according to the vacuum pad
instructions.
Using the Shoring Pin
For added rigidity, when using an expansion-type
anchor or vacuum system, use the shoring pin and
a brace.
1. Secure the stand using either an expansion-type
anchor or a vacuum system. WARNING! Never
rely on the shoring pin alone for securing.
2. Use wood (e.g., 4"x4" piece of lumber) to brace
stand between a sturdy structure and the top of
the stand.
3. Use the eye bolts (4) to level the stand. Check the
4. Cut a piece of lumber slightly longer than needed.
the drill.
Use a MILWAUKEE MX FUEL ™ Core Drill with
this stand.
1. Remove the battery pack.
2. Remove the feed handle from the carrier. The feed
3. Install the feed handle into the locking shaft of
4. Fully loosen the locking
5. Hook the mounting plate
6. Slide the lock shaft back
7. Remove the feed handle from the locking shaft
8. Ensure the carrier and drill are fully seated and
9. To remove drill, reverse the procedure.
Anchor plate
Select the proper style and size bit for the job. Always
use clean, sharp, and properly maintained bits.
1. Remove battery pack.
2. To install the bit, thread
3. To remove the bit, rotate the collar by hand to re-
6
bubble level to ensure the stand is level.
Wedge the piece of lumber between the stand and
the above structure.
Mounting the Core Drill to the Stand
To reduce the risk of injury, always
WARNING
remove battery before installing
handle is also used to install the drill.
the carrier.
shaft and then slide it out
of the carrier (it will be
retained in the housing).
over the mounting pin
and set the drill into place.
Ensure the mounting plate
is flat against the carrier.
into the carrier, and tight-
en securely with the feed
handle.
and place it into the desired feed handle location.
check tightness of the lock shaft before operating
the machine.
Selecting and Installing a Core Bit
the bit securely onto the
spindle. Use a wrench on
the flats to tighten the bit
securely. Do not contact
the collar during installa-
tion, the collar will loosen, and the bit will not be
threaded on securely.
lease. Thread off the bit once the collar is released.
If the bit does not release use two adjustable
wrenches to unthread; one on the bit and one on
the flats on the shaft.
Mounting pin
Locking shaft
Flats
Collar
Spindle
Publicidad
